Add wireless camera control to your SmallHD Smart 7 monitor using a Bolt 4K LT RX with this Teradek USB to 5-Pin Adapter for Bolt 4K LT RXfrom Teradek. The adapter is part of the Wireless Camera Control Kit for the Teradek Bolt 4K series, designed to facilitate wireless camera control when you have the Smart 7 optional SmallHD camera control software license installed for your camera.

The unit plugs into the USB port on the bottom of the Bolt 4K LT RX and provides a 5-pin connector to facilitate the wireless connection.

Control Camera via SmallHD 7" Monitors    Add Wireless Camera Control to Monitor    Connects to Bolt 4K LT RX    USB to 5-Pin Connectors

Teradek Bolt 4K LT RX
SmalHD Smart 7 monitor series

Related Questions and Answers

Q: 1. Does Transmitters have a vmount plate? or is this only for the receivers?

A: While the Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless RX/TX Deluxe Kit (V-Mount) only has a V-mount plate for the receiver, you could add the Teradek Single-Battery Plate for Bolt (Female, V-Mount), B&H # TE110854, to the transmitter.

Q: 2. Will this battery plate work on the Bolt 500 LT (HDMI) Rx Receiver?

A: No, the Teradek Bolt 1000 LT and 500 XT RX Battery Plate (V-Mount) does not direct mount with the Teradek Bolt 500 LT HDMI Wireless RX and provide power through the JST connector. Instead, consider Teradek Single V-Mount 14.4V Battery Plate for Bolt Pro 300/500/600/1000/2000/3000 Receivers, which come with mounting, the plate, and a power cable. See the link below: https://bhpho.to/3AChkD8

Q: 3. Can the Bolt 6 Receiver HDMI receives signal from from a Bolt 6 SDI/HDMI version?

A: The Teradek Bolt 6 LT HDMI 750 Wireless Receiver can receive the signal of any bolt 4K series transmitter, including the transmitters that SDI/HDMI inputs.

Q: 4. Does Bolt 6 HDMI pass start/stop flags of Canon R6 or Red Komodo? (I have tried but I can't get it to work)

A: The Teradek Bolt 6 LT HDMI 750 Transmitter/Receiver Kit is not listed as being able to start/stop camera recording.

Q: 5. Hello, will this fit the new Teradek 6 LT series either the 1500 & 750 receivers?

A: No, the Teradek Bolt 1000 LT and 500 XT RX Battery Plate will not support the Teradek 6 LT. Please work with the plates listed below. The plates below will work with the 1500, and 750 Transmitter, or Receiver. Female Battery side V-mount: Teradek Single-Battery Plate for Bolt (Female, V-Mount) BH #TE110854 Male Camera side: Teradek V-Mount Battery Plate for Bolt 4K Monitor Module (Male, Camera Side) BH #TE110855

Q: 6. Can this transmit camera control in addition to the video? I have a small hd 702 touch with a red software license for camera control but need to know if this will support it

A: Yes, the Teradek Bolt 6 LT can be combined with SmallHD Smart 7 Monitors and Wireless Camera Control Starter Kits, allowing you to wirelessly control RED, ARRI, and Sony VENICE cameras.

Q: 7. Are these better than the original that come with the kit?

A: If you have an older Teradek Bolt 4k LT the antennas will now allow you to support 6G signals. This is a kit of 7 antennas meant to replace the original antennas sold with Bolt 4K LT HDMI. These antennas, along with the latest Bolt 4K LT HDMI firmware ( https://bit.ly/3vhrPMF ), will allow Bolt 4K LT HDMI to access 6GHz frequencies (region dependent).

Q: 8. Will this mount to a Bolt 6 TX?

A: Yes, the Wooden Camera Offset Mounting Bracket for Teradek Bolt 4K LT TX is also fully compatible across the Bolt 6 ecosystem's TX.

Q: 9. How many LT 750s can operate in the same area?

A: These are point to point systems and while multiple units may be employed on a single set or location, each transmitter can support up to six receivers.

Q: 10. Will this fit the updated Bolt 6 LT TX? I have the HDMI version

A: The dimensions on paper would appear to work for housing the newer Teradek Bolt 6 LT series TX. We will not be able to test this unfortunately.