Add wireless camera control to your SmallHD Smart 7 monitor using a Bolt 4K LT TX with this Teradek USB to 5-Pin Adapter for Bolt 4K LT TXfrom Teradek. The adapter is part of the Wireless Camera Control Kit for the Teradek Bolt 4K series, designed to facilitate wireless camera control when you have the Smart 7 optional SmallHD camera control software license installed for your camera.

The unit plugs into the USB port on the bottom of the Bolt 4K LT TX and provides a 5-pin connector to facilitate the wireless connection.

Control Camera via SmallHD 7" Monitors    Add Wireless Camera Control to Monitor    Connects to Bolt 4K LT TX    USB to 5-Pin Connectors

Teradek Bolt 4K LT TX
SmalHD Smart 7 monitor series

Related Questions and Answers

Q: 1. Can I use more than one tx / rx pair in the same environment?

A: It should theoretically be possible to use 6 Teradek Bolt 6 LT HDMI 750 Transmitter/Receiver Kits in a single location if you are all using fixed frequencies and there is minimal external interference in the area. The spacing of the equipment will also be incredibly important. With the Bolt 6 you'll want to have at least 10 feet between the transmitter and the receiver, and between other sets. If more receivers are used in a set this will impact the communication even more so. The Bolts operate in the unlicensed 5 GHz spectrum which can be use by other devices like WiFi routers, other wireless transmitting systems, etc. Here is an article that may be helpful: https://support.cs.inc/s/article/Bolt-4k-Best-Practices-for-Interference

Q: 2. Is there a PTap port on the Anton Bauer plate to power other accessories?

A: Please note that the Teradek Bolt 6 LT HDMI 750 Wireless Receiver BH #TE102267 does not come with a V-Mount plate. The following Teradek Blot 6 comes with a V-Mount battery plate and one DTap connector on the plate. Teradek Bolt 6 LT HDMI Wireless Receiver (V-Mount) BH #TE102267V

Q: 3. Can the Bolt 6 Receiver HDMI receives signal from from a Bolt 6 SDI/HDMI version?

A: The Teradek Bolt 6 LT HDMI 750 Wireless Receiver can receive the signal of any bolt 4K series transmitter, including the transmitters that SDI/HDMI inputs.

Q: 4. Are these better than the original that come with the kit?

A: If you have an older Teradek Bolt 4k LT the antennas will now allow you to support 6G signals. This is a kit of 7 antennas meant to replace the original antennas sold with Bolt 4K LT HDMI. These antennas, along with the latest Bolt 4K LT HDMI firmware ( https://bit.ly/3vhrPMF ), will allow Bolt 4K LT HDMI to access 6GHz frequencies (region dependent).

Q: 5. Does this only work with the transmitter, or can it be fitted to the receiver as well?

A: This can technically be mounted to any 1/4" 20 thread, but is specifically designed for the Teradek Bolt 4K TX.

Q: 6. If the Tx is fed signal via HDMI, will the local BNC loop thru / output transcode that signal lien the older 500 units did?

A: Yes, the Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless Transmitter supports HDMI cross conversion. This would allow the HDMI input to output through the 3G-SDI. The Teradek Bolt 6 also would downscale 4k signals from HDMI to HD when outputting via the 3D-SDI.

Q: 7. Will this fit the updated Bolt 6 LT TX? I have the HDMI version

A: The dimensions on paper would appear to work for housing the newer Teradek Bolt 6 LT series TX. We will not be able to test this unfortunately.

Q: 8. Does Bolt 6 HDMI pass start/stop flags of Canon R6 or Red Komodo? (I have tried but I can't get it to work)

A: The Teradek Bolt 6 LT HDMI 750 Transmitter/Receiver Kit is not listed as being able to start/stop camera recording.

Q: 9. If I buy the kit without a V mount plate where can I get it later if I want to? I can't find the same one they use.

A: The Wooden Camera Dual Battery Plate Cradle for Teradek Bolt LT Transmitter (V-Mount) is the respective V-Mount plate for the Teradek Bolt 6 LT HDMI 750 Wireless Receiver.

Q: 10. Will this mount to a Bolt 6 TX?

A: Yes, the Wooden Camera Offset Mounting Bracket for Teradek Bolt 4K LT TX is also fully compatible across the Bolt 6 ecosystem's TX.