The Bescor MP101 MP6VA L-Series Plate 5VUSB MPDTAP Kitattaches between a tripod and camera and enables remote panning and tilting of the camera. Two independent motors smoothly operate horizontal and vertical motion at adjustable speeds. The head supports payloads up to 6 lb. The two mounting points are the 1/4"-20 female threads underneath and the 1/4"-20 camera mounting screw with registration pin on top. All tripods and cameras are compatible.

An Auto Pan Mode allows for continuous panning motion, and a switch selector lets you assign end points at 45°, 90°, or 340°. The maximum horizontal angle is ±170 degrees, and the maximum vertical angle is ±15 degrees. This head can power by four AA batteries, the Bescor PS-260 AC power supply, or a Bescor 90-645 external battery, all sold separately.

MP101 Motorized Pan/Tilt Head Kit    D-Tap Power Adapter Cable & USB Cable    L-Series Plate, Battery & Charger    50' Remote Extension Cable    PS260 AC Power Adapter, Remote Control

• Enables panning and tilting of a camera remotely at adjustable speeds
• Attaches between a tripod and camera
• 1/4"-20 threads for tripod; 1/4"-20 screw mount for camera
• 6 lb payload
• Remote control included

Related Questions and Answers

Q: 1. Does this power supply convert the 14.4V coming from my V-Mount batteries to a safe for the X-T3 7.2V? I assume it does but it doesn't explicitly say this anywhere and I don't want to fry my X-T3 with double the rated voltage input.

A: Yes, the Bescor NPW126SDTAP Coupler/Dummy Battery & D-Tap Adapter Kit for Select FUJIFILM X-Series Cameras (B&H# BENPW126SDTP) kit, when used as a whole (i.e. with both its D-Tap style plug and cable and dummy battery) will convert the voltage to the appropriate level for your camera from a 14.4V, 14.6V, or 14.8V power source. Typically, that source would be a V-Mount battery. More than 90 percent of V-mount batteries sold are in the 14-14.8V voltage range, and those will be fine. Please do not use the Bescor NPW126SDTAP Coupler/Dummy Battery & D-Tap Adapter Kit for Select FUJIFILM X-Series Cameras (B&H# BENPW126SDTP) with batteries or power supplies of other voltages such as 12.6V, 26V, or 28V.

Q: 2. What is the output of the AC adapter, in volts/amps?

A: The output is 9v/2amps.

Q: 3. Is this a 5.5 mm barrel?

A: Yes, the barrel of the Bescor 2.5mm Female to 2.5mm Male Power Extension Cable for MP101 would be 5.5mm.

Q: 4. Will this provide the proper output voltage of the input is lower than 14 volts? Mine will be providing about 7.4 volts. Thanks!

A: The Bescor NPW126SDTAP Coupler/Dummy Battery & D-Tap Adapter Kit for Select FUJIFILM X-Series Cameras is regulated to output the proper power for the following FUJIFILM cameras: - X100F - X100V - X-Pro3 - X-T3 - X-T30

Q: 5. is the rechargable battery portable? Or do I always need to have it plugged in if I am not using AA batteries?

A: The batt is portable. The kit is nice

Q: 6. I think i know the answer based on the other Q&A - will work properly with the X-Pro2?

A: Yes

Q: 7. What's the dc jack size of this item?

A: The DC jack size of this item is.Outer diameter is 3.5 mm.Inner diameter is 1.1 mm.

Q: 8. can you close the battery door if you use it with an X-T3?

A: Yes, the XT3 has a rubber gasket by the door to allow for a cable to fit.

Q: 9. Hi would this work with the Fuji HS50EXR? That uses the NP-126 battery (not S type) so it should work with this too?

A: No, the Bescor NP-W126S Dummy Battery & AC Adapter Kit for Select FUJIFILM X-Series Cameras is not compatible with the FUJIFILM FinePix HS50EXR.

Q: 10. How do I mount the LED 950 light to the Bescor tripod ??

A: This LED panel would screw into the Bescor tripod or stand using a 1/4 thread at the bottom.