The Camplex 6' Lemo to Duplex ST Fiber & 6-Pin AMP Cablefrom Camplex 6' Lemo to Duplex ST Fiber & 6-Pin AMP Cableis a certified multistage machine polished cable exceeding SMPTE specifications. This cable features a Lemo PUW connector feeding out to both Duplex ST optical connectors and a 6-Pin AMP connector for power.

Assembled with premium SMPTE cable & LEMO and Senko connectors

Industry standard cable

Terminations by LEMO trained technicians

Electrical assemblies 100% tested for continuity and short circuits

Fiber optic assemblies 100% tested for attenuation and back reflection

SMPTE 311M and 304M compliant

Stainless steel assemblies

Rubber dust caps

19.4 Mb/s to 3 Gb/s transport speed

Machine polished fiber contacts

Low insertion and return loss

Related Questions and Answers

Q: 1. Has anyone used this for AUdio? I have a 5pin lemo audio out on my camera and would like to connect this to my stereo mini jack

A: This cable, as stated, is designed for Timecode. HOWEVER, if the connections inside cable and inside your camera are wired the same, it may work.Its impossible to tell without knowing the camera wiring of its connector. I would contact your camera manufacturer.

Q: 2. Will this connect to the z cam e2 s6 to ride video mic pro?

A: No, the Tentacle Sync Tentacle to 5-Pin LEMO Cable is not intended for use to connect a microphone to the Z CAM E2-S6 Cinema Camera. It is designed to send a timecode signal from a Tentacle Sync timecode generator to any camera or recorder using a 5-pin male LEMO input. The Rode VideoMic Pro has a 3.5mm TRS output which can be connected directly to the camera's 3.5mm TRS mic input. The camera's 5-pin LEMO port is intended to be used for dual-channel XLR microphones and requires an additional XLR audio connector like the CAMVATE Dual 3-Pin XLR to Right-Angle 5-Pin LEMO Audio Cable for ALEXA Mini (B&H # CAC2723) or for single-channel, the CAMVATE 3-Pin XLR to Right-Angle 5-Pin LEMO Audio Cable for ALEXA Mini (B&H # CAC2722).

Q: 3. is compatible with arri2 2 pin conector?

A: Lemo ports on Letus Helix are reversed polarity from most equipment with Lemo connections. Not sure but Arri might also be reversed polarity.

Q: 4. Can this work with the red Komodo x 5 pin input?

A: No, not for timecode. The RED DIGITAL CINEMA KOMODO-X 6K Digital Cinema Camera uses a 9-pin LEMO connector for timecode. The Tentacle Sync C21 Tentacle to RED KOMODO Adapter Cable (B&H # TEC21) would be the cable to use for timecode with the RED Komodo-X. The camera's 5-pin LEMO connector is for audio input/output.

Q: 5. How long is this cable?

A: The manufacturer does not specify this information and since this is a brand new item, which we currently do not stock yet, we have no possibility of physically verifying this at this time.

Q: 6. Can I use this cable on my red komodo tilta advance power distrobution module with RS port and ARRI cforce RF / cmotion cPRO Motor to do wireless run/stop on the follow focus remote?

A: This Tilta 3-Pin Fischer to 4-Pin LEMO Cable (22") is only designed for power and will not trigger run stop!

Q: 7. Is this male to male?

A: Yes, this is a Tilta 2-Pin to 2-Pin LEMO Cable (23") male to male.

Q: 8. can you power the new SMALLHD INDIE 7 monitor with this cable?

A: No you can not. You should use this to power the Indie 7 Monitor instead. SmallHD D-Tap to L-Series Dummy Battery Cable (32") BH #SMDTSLFB • MFR #PWR-ADP-SONYL-DTAP

Q: 9. Product description does not indicate if the 5 Pin Lemo is male or female. I would expect that it is Male?

A: Yes it is a male connector.

Q: 10. How long is this cable?

A: The Tilta 2-Pin to 4-Pin LEMO Cable is 17cm in length.