This 3-Channel Datavideo 3-Channel HDBaseT Receiver HDMI Outputssupplies power, Ultra HD 4K50/60 video, and camera control to up to 3 devices up to 328' distance. It simultaneously outputs HDMI, RS-422, and IP control signals.

Link 4K and 1080P Cameras    Converts IP Video to HDMI Output

HBT-30 can power PTZ video cameras via PoE, transmit signals over a single ethernet cable to and from the camera, and can be used to remotely control various camera parameters such as iris, presets, etc. Most importantly, it can output 4K HDMI signals to your switcher.

HBT-30 transmits 4K HDMI signals as well as camera control. With the HBT-30, the system can be integrated as a camera controller, video switcher, and ISO recorder.

Remote control of camera functions via RS-422 or DVIP with up to 3 cameras simultaneously up to 328'.

HDBaseT allows you to transmit video, control, tally, and power over a single Cat 6 cable. This means you no longer need to run multiple cables for your cameras.

Related Questions and Answers

Q: 1. Is it possible to have 5 inputs in MW. One must be in the middle of other 4 inputs in corners?

A: Yes you can have 5 inputs in the multi-view.

Q: 2. is it possible to have 5 inputs in the MW. one must be centered in the middle of MW?

A: Yes

Q: 3. Can I use HD cameras with this? Is there anyway I can output at least 720 for live stream purposes?

A: Hi Dashawn, Unfortunately, our SE-500 is an Analog only switcher so you won't be able to use any HD signals with it. However, if you would like to up convert the Composite output of the SE-500 to HD-SDI at 720p, you'll be able to do that by using our DAC-7 and DAC-70 converters. DAC-7 can up convert an Analog Composite signal to Digital SD-SDI. Then, you can take the 480i SD-SDI signal from the DAC-7 to the DAC-70 up/down/cross converter to convert to HD-SDI or HDMI at 720p signal. Thanks!

Q: 4. Is The Power Supply Auto Switching? 110/220v?. Also May i know what size is the tip of the power connection? Just In Case We Misplaced the original power supply, can we use a different one? Or where can we find the original power supply just for backup? thanks

A: Hi Lemuel,Yes, the power supply is auto switching for 110/220 voltages. Datavideo power supplies utilize a standard DC Barrel Connector which have a 5.5mm outside diameter and a 2.5mm inside diameter on the male connector and are wired center pin positive. Replacement power supplies can be sourced through a local reseller or direct from Datavideo. Thanks!

Q: 5. Can i configure to view only four inputs on one screen? Can change back to six or four on the fly using USB/PC ?

A: Yes

Q: 6. Is it possible to split each (or any) of the 2 Video Outputs to get 4 separate Video Outputs so that I can connect to 4 TV monitors with the SE-500? If so, what cables do I need?

A: Hello, hope whoever is reading this is having a good day!!. I was wondering if i could buy the comm system and the screens separately and will they work with the PAL version??..

Q: 7. Will this unit embed audio transferred via the RCA inputs, into the HDMI out stream? Is there a method to assure video-audio sync?

A: The answer to both questions is that you can sync the audio and it will go out HDMI embedded.

Q: 8. Is it glitch-free switching between inputs?What is latency beetween in and out? Thanks!

A: Switching is fast and glitch free.

Q: 9. Can the Datavideo SE-500DH record separate input channels to another device? If so, what do you recommend?

A: Unfortunately it will not. That is not possible with this switcher. For ISO recording of each input you'd need to look at Software and Computer Based Switching solutions. The Telestream Wirecast Gear 110 is a great option to consider, BH #TEWCGEAR110. https://bhpho.to/2kPYog8

Q: 10. 1. What happens when signal lost or disconnect one of the SDI input - does it show black on missing input or show some test patterns or solid color?2. Can we disable audio meters / file names / input names to have clean multi-view feed to monitor?

A: Got Answer from Chris.H (Thank you) B&H and Decimator The DMON-6S can be set up to either generate its own reference (free run) or use one of the inputs as a reference. If its set up to use free run or an input other than the one thats pulled then it will continue to show an output with just that window showing its background colour. The background colour can be selected in the USB Control Panel software, available free of charge for Windows and Mac. For the application your customer has described I would recommend setting it up so that Reference is set to Free Run nd background colour is set to black.You can remove all in picture overlays (audio meters, graticules, UMDs and status displays) from the multi-view output to show just the input sources.