The ARRI TRINITY 2 Joystick Set for Analog Controlfrom ARRI TRINITY 2 Joystick Set for Analog Controlis compatible with the TRINITY 2 Stabilizer. This set consists of an analog joystick and a clamp-on tube mount.

Analog Joystick for TRINITY 2 Stabilizer    Joystick/Monitor Tube Mount

Related Questions and Answers

Q: 1. Can this pan 360 degrees continuously or once it makes a full revolution does it need to rotate back. It appears the cables run through the center of the frame. Is there enough room in that opening to fit a small zoom control cable?

A: Yes. It can be mounted vertically or underslung. The Head will pan and tilt through 360°, and this enables the camera to point directly upwards or downwards when required.

Q: 2. Sony's site says this is compatible with the FX9. Do you know if it is compatible with the FX6 or FX3?

A: The RCP1000/1500 has an Ethernet interface. If used with the XDC-FX9, the FX9 is compatible. The other two models (FX6/FX3) are not.

Q: 3. Can I mount this on an iFootage M1-III Mini Crane Jib Arm (BH #IFM1III MFR #M1 III)?

A: Yes you can.

Q: 4. Can the dimensions of this Proaim gold head accept the BMD URSA Broadcast G2 Camera with Fujinon 8.5-170mm Digital Servo Lens?

A: The Proaim Gold Pan/Tilt Head width is 20cm (7.874 inches). The payload weight is 16lbs. The URSA Broadcast G2 is 5.9 inches wide and 9 inches tall with the handle attached. The handle can be removed to make the camera more compact when used on the head. The URSA weight is 7.83 lb. The Fujinon 8.5-170mm should be 3.26 lbs. The total payload of the camera and lens would be about 11lbs and keep you under the payload weight of 16lbs for the PTZ head.

Q: 5. How noisy is it? Compared to the VZ-MC50? Will a nice boom mic, like an MKH 416, pick it up from a few feet away?

A: It is not unduly loud. A nice boom mic, properly positioned, will not pick up the noise from the motors.

Q: 6. Does this work with the Proaim Alphabet 21' Jib/Crane Arm?

A: Yes, The Proaim Jr Pan/Tilt Head with Joystick Control (12 VDC) would be compatible with the ProAim Alphabet Jib models.

Q: 7. Any idea how to control Zoom and Focus using this head?

A: As far as we are aware, the controls on the Proaim Jr Pan/Tilt Head are for the pan and tilt head exclusively, and do not interface with the camera or control it. I believe the easiest way to control your camera's zoom/focus while it is on a crane or jib would be a wireless follow focus system.

Q: 8. will this work with ptz optics cameras?

A: Yes, the PTZCam View NDI PTZ Controller with NDI|HX Preview and Joystick Control is compatible to control PTZOptics cameras.

Q: 9. Can I mount it on a ProAm USA Orion DVC210 DSLR Video Camera Jib Crane Tilt Stand? Do I need any adapter plate?

A: The Proaim PTJR can mount to many jibs but the weight support of the ProAim Orion is not sufficient for the PTJR to be supported. It would work with other jib models that have a higher weight capacity.

Q: 10. What frequency? Square or sine wave output?

A: The Antelope Isochrone Trinity Master Clock Generator (B&H # ANISOTR) features three (3) independent and simultaneous audio generators up to 384kHz and varispeed control +/- 200 cents. It is a 10 MHz atomic master clock. There are no documents that address sine/square wave specifications.