Whether you are a seasoned creator or new to the world of 3D printing, the Polymaker 1.75mm PolyTerra PLA+ Filament Greenenables you to explore your imagination, bringing your designs to life.

Retaining the best properties of PLA and enhancing them for optimal adhesion and strength. This PLA+ material provides a recyclable and natural thermoplastic polyester suitable for printing a litany of highly resistant creations. PolyLite PLA+ has a printing speed range between 30 to 70mm/s and a temperature range of 374 to 446°F. This filament supports direct and indirect drive systems with a retraction distance and speed of 1mm at 20mm/s and 3mm at 40mm/s, respectively. Each spool and box is made from recycled material, ensuring a positive impact on the environment.

1.75mm Diameter    1kg Weight    374-446°F Temperature Range    30-70 mm/s Printing Speed Range    Direct & Indirect Drive Compatible    Support for Heated Beds

Related Questions and Answers

Q: 1. Carry Handle? Why would then not put the same FX handle on top. I have concern about the carry handle because I don't always use a shoulder strap bu have not seen ANY photos of the carry handle for this bag, even on the Tiffin site. Must not be very proud of their design.

A: This bag, a classic for over 40 years, never had a handle on top.

Q: 2. Is this good for the 7D with a zoom on?

A: I used mine on safari with a 55-300 zoom and it worked well on the top of their vehicle. I will admit that I used their bean bag more often only because it was so much wider than the pod that I could leave it slightly over the edge of the vehicle and it would stay put allowing me to change lenses more easily. The green pod worked great though

Q: 3. #1 Small enough for airplane carry on?#2 Will it fit in overhead bin of airplaneThank you

A: Place under seat until takeoff, then place under feet to improve blood circulation on long flights.

Q: 4. Would it be practical to lay a 17-inch (folded) tripod across the top, underneath the hand straps while carrying the bag by the shoulder straps?

A: It may be a risk of damaging your gear if the tripod is under the hand straps and the top flap.

Q: 5. Can anyone suggest a light travel cart that would work with a full F2 (including side pockets)? Had recent shoulder surgery and can’t carry yet this is still one of the best camera cases for working on location.

A: The Travel Smart by Conair Folding Multiuse Cart (Black), BH # TRTS36C would be a suitable option for holding a Dome F2 that is fully packed. http://bhpho.to/3i1vCCU

Q: 6. Will it take a canon EOS60d plus lenses and stuff ?

A: Yes you would have more than enough room for your equipment listed.

Q: 7. Could this bag carry EFS-18-55mm macro lens,EF 75-300mm F/4-5.6III,EF 70-200mm F/4L IS USM Canon Rebel T5 1200D camera and accessory?

A: Yes, it will hold all your gear.

Q: 8. can the divider be removed completely?

A: Hi, that divider is sewn in, so it's not removable.

Q: 9. Regarding wax finish; presuming material is much like many Filson waxed materials. Was not impressed by Tiffen Rep stating "shouldn't be a problem" DAUGH...NO IT SHOULDN'T. So have any of you tried waxing then warming with hair dryer and wiping down with clean cotton cloth to enhance water resistance and improve appearance while eliminating the greasey fee of excessive wax? I just wish it had the FX2 hand strap in addition. Maybe a couple slots for pen & penlight.

A: This bag has been a classic for 40 years and is perhaps the favorite bag of professionals. Any issues during that time seem not to be insurmountable.

Q: 10. It says DSLR but will it work with mirrorless cameras?

A: Yes it will work with a mirrorless camera..