Primarily designed for 1/8 and 1/10 scale RC cars, such as the Slash 4x4 Ultimate and Traxxas Bandit, this Gens Ace 7200mAh 4S 14.8V 60C LiPo Battery Deans Plugfrom Gens Ace 7200mAh 4S 14.8V 60C LiPo Battery Deans Plugdelivers steady and safe power. Priding itself on providing consistent voltage, even under load, this battery offers up to 14.8V with a 7200mAh capacity. It comes equipped with a Deans plug, as well as a JST-XH balance connector.

For 1/8 & 1/10 Scale RC Cars    Made for Steady Voltage Under Load    7200mAh Capacity    4S, 14.8V, 60C LiPo Configuration    Deans Plug    JST-XH Balance Connector    Supports 5C Fast Charging    Works with 1/8 & 1/10 Balance Chargers    EFRA Approved

• Works with LiPo balance chargers for 1/8 and 1/10 scale RC cars
• JST-XH balance connector
• Supports 5C fast charging
• EFRA approved

Related Questions and Answers

Q: 1. Can I use a Gold mount battery with this V-mount adapter, by attaching the Intellytech Gold Mount to V-Mount Battery Converter Plate (https://www.bhphotovideo.com/c/product/1259292-REG/intellytech_175000_anton_bauer_gold_mount.html)?

A: No. Locking system must be converted over. A end-user is better off just buying gold mount batteries to power there unit. Please review the following item GVM V-Mount Battery with D-Tap and DC Outputs BV-95 BH #GVBV95 • MFR #BV-95 https://bhpho.to/36IMld1

Q: 2. Can a CRMX receiver pull power from the unit while plugged into it? Like the TimoLink RX Wireless DMX Receiver USB-C input?

A: No, the USB-A port on the Nanlite Forza 60C RGB LED Monolight is only for updating the firmware. This cannot be used to power other devices.

Q: 3. Is there Artnet support with the WiFi connection?

A: No, Nanilte does not list that Nanlite Forza 60C RGBLAC LED Spot Monolight Kit works with Artnet.

Q: 4. What is a good accessory to add wireless ArtNet support to this fixture? Says one can connect DMX and the USB could be used to power a wireless connector in the brochure, but which accessory would be needed for that?

A: What you may use first is the Nanlite DMX Adapter Y Cable for Forza 150, BH # NACBDMX35C12 to give you the DMX connections on the Forza 60C. This would be followed by the Kopul DMX35PA-S 3-Pin Male to 5-Pin Female DMX Adapter Cable (6"), BH # KODMX35PAS and then the Blizzard SoC-It Wi-Fi Wireless DMX Gateway Control Solution, BH # BLSOCIT. https://bhpho.to/3IVh99j https://bhpho.to/3IXxBpj https://bhpho.to/3o2FtfH

Q: 5. When I shut off the power to the Forza 60C and switched it back on it lost the hue/color setting. Is this normal?

A: No, setting for the Forza 60C should be held in place after every turn off or on.

Q: 6. Is this compatible with the Tricaster 2 Elite. What cable to I need to connect the two?

A: The Digital Arts metaSETZ TLC-4S Tally Controller for TriCaster simply connects to the NewTek Tricaster Elite via a USB Cable.

Q: 7. Is there a DC extension cable that plugs into the light?

A: No. We usually suggest investing in a AC power extension cord.

Q: 8. Hi I have a AV Matrix VS0691 with GPIO tally interface would this work with that Video Switcher?

A: According to the manufacturer, only Tricaster models are with the supported with the Digital Arts metaSETZ TLC-4S, however the manufacturer also states about their TLC-U model: "Other Switchers – If it’s got a tally port we can make it work. With 9, 15, 25 and 37 pin variants the TLC-U supports most switchers". The Digital Arts metaSETZ TLC-U can be found here with a 15 pin connector (SKU: DITLCU15) https://www.bhphotovideo.com/c/product/1476966-REG/digital_arts_tlc_u_15_8_output_tally_controller.html http://www.metasetz.com/wordpress/metasetz/

Q: 9. Which v-mount batteries are compatible with this? I used a green extreme v-mount battery to power it and it caused the light to blow..

A: Any V-Battery is compatible.

Q: 10. can I use 16.8v battery with this?

A: yes, but will cut into run time and must feature a 2.1mm barrel and D-tap output in order to power up properly.