The 100-pack of 75-Ohm BNC Connector for RG6 Cable - Kings Electronicsare connectors designed to meet SMPTE 259, 274, and 292M standards, and has excellent performance to 3 GHz. This 3-piece connector has a tarnish-resistant alloy electrodeposit finish on the body and bayonet, and a gold-plated center conductor. The connector fits RG6, including Belden 1694A and 1695A, West Penn 6350 and 256350, and Gepco VSD2001. Recommended Kings KTH-1000 crimp tool with KTH-2325 die.

Kings 2065 series connectors meet the stringent requirements for HDTV, exhibiting return losses of less than -36 dB to 1 GHz, -25 dB to 2 GHz, and -23 dB to 3 GHz. Precision machined to extremely tight tolerances, they are built with the toughness needed for the broadcast environment. Minimum 500 mating cycles. Winchester KINGS brand 75-ohm BNC series RF connectors have a reduced dielectric to achieve 75-ohm nominal impedance. All the connectors in this group have captive center contacts.

Fits Belden 1694A and 1695A    Fits West Penn 6350 and 256350    Fits Gepco VSD2001    Gold-Plated Center Conductor

Related Questions and Answers

Q: 1. Does the Tentacle Sync Tentacle to BNC Cable (Straight, 16 ) work with the BMD HyperDesk Mini single one directional RF BNC Input?

A: The Tentacle Sync (C06) BNC TC cable is designed for bi-directional use. Being that you are looking to send timecode out, and into the BMD HyperDesk Mini, I would recommend a one directional TC/OUT cable from ambient; B&H# AMBNC3.5.

Q: 2. What is the bandwidth of this cable?

A: Unfortunately, the manufacturer does not supply that exact spec, but they do classify this as a 3G-SDI cable, so it will be able to carry up to 1080 at 60p.

Q: 3. What is the power supply for this? I am researching the image for low light insect photography. What does the image look like?

A: We currently don't have any sample of the footage taken from the camera. It is possible for it to be found online. The following is the power supply recommended be Marshall Electronics.

Q: 4. Will this work with FS5 and Atomos Inferno?

A: Hi Branden, If you talking about the Atomos Inferno SDI version, you will be satisfied. We hope this helps and we thank you for your interest in our products. The SHAPE team

Q: 5. Are these Shielded Cables?

A: No, the cables included in the SHAPE BNC 1st AC Camera Cable Kit are not shielded.

Q: 6. Can I use this cable to connect GH5 timecode out, which is BNC to the Sound Devices Mix Pre 6 II 3.5mm timecode port?

A: The Mix pre 6 II 3.5mm stereo out is capable of doing timecode, so yes it will work.

Q: 7. Are these cables shielded?

A: the manufacturer description does not indicate that these are shielded

Q: 8. Is this connector a two pin male?

A: This has a Conxall connector for select Marshall products.

Q: 9. Can I use this connector on RG-6 plenum cable (Comprehensive RG6 SDI/HDTV 18 AWG BC)?

A: At this time, we are recommending these three following plugs, Comprehensive BP-2C7559 75 Ohm Male BNC Connector for RG-59 Coaxial Cable B&H # COCB, Canare 3.0 GHz 75-ohm BNC Plug for Canare L-5CFB/V-5CFB Cable B&H # CABCPB5F, and Comprehensive BP2C7559P 75 Ohm Male BNC Connector for RG-59 Plenum Cable B&H # COCBPQ. If your budget is constrained, go for the most affordable. If you need better quality, go for the higher priced connectors.

Q: 10. Can I connect this to the timecode out on the Zoom F4 and into the mic input on the BMPCC 4K and have a perfect sync? (It will always be connected)

A: You can use this cable to connect the TC out of the F4 to the mic input of the BMPCC. It will need to be connected the whole time, and the TC will be recorded as an audio squarewave onto the track. Once your recording is done, you will need to convert the audio TC to usable TC via a production app like Adobe Premier, Davinci Resolve, or Tentacle Sync Studio.