The 100-pack of Kings Electronics 75-Ohm BNC Connector for Belden Cablesis designed to meet SMPTE 3G/6G/12G SDI requirements, and has excellent performance to 6 GHz. Each connector has a nickel-plated body, silver-plated spring washer, and a gold-plated center conductor. They fit sub-mini serial digital coax, including Belden 1855A and 1865A, West Penn HD825 and HD25825, and Gepco VM230.

Recommended for installation are the Kings KTH-1000 crimp tool with KTH-2025 die. Kings 2065 series connectors meet the stringent requirements for HDTV. Precision machined to extremely tight tolerances, they are built with the toughness needed for the broadcast environment with a minimum 500 mating cycles. Winchester Kings brand 75-ohm BNC series RF connectors have a reduced dielectric to achieve 75-ohm nominal impedance. All the connectors in this group have captive center contacts.

Fits Belden 1855A and 1865A    Fits West Penn HD825 and HD25825    Fits Gepco VM230    Gold-Plated Center Conductor

Related Questions and Answers

Q: 1. Are these adapters directional? Or does signal get converted both ways?

A: The Canare BCJ-XP-TRC Digital Audio Impedance Transformer is used to passively convert 75 ohm BNC coaxial cable to 110 ohm/XLR3 standard AES/EBU digital audio signal. The input is a BNC female receptacle (75 ohm) and the output is an XLR 3-pin male connector (110 ohm). It is a directional adapter.

Q: 2. Would these cables work instead of the more expensive AM2 cables on a G3 receiver?

A: Yes, these cables will work in the same way as the AM2 cables.

Q: 3. What is the power supply for this? I am researching the image for low light insect photography. What does the image look like?

A: We currently don't have any sample of the footage taken from the camera. It is possible for it to be found online. The following is the power supply recommended be Marshall Electronics.

Q: 4. Is it better to used for lows bass or mids and highs?

A: Frequency Response 20Hz - 20kHz, +0, -1 dB

Q: 5. Is this 9 pin connector compatible with Sony PTZ cameras and controllers similarly equipped?

A: If your Sony camera model has a Phoenix port for RS-422 control (many Sony models do not offer this port today), the Marshall Electronics RS-422 9-Pin Phoenix Connector for CV620/CV612 PTZ Cameras will work.

Q: 6. Can I use this connector on RG-6 plenum cable (Comprehensive RG6 SDI/HDTV 18 AWG BC)?

A: At this time, we are recommending these three following plugs, Comprehensive BP-2C7559 75 Ohm Male BNC Connector for RG-59 Coaxial Cable B&H # COCB, Canare 3.0 GHz 75-ohm BNC Plug for Canare L-5CFB/V-5CFB Cable B&H # CABCPB5F, and Comprehensive BP2C7559P 75 Ohm Male BNC Connector for RG-59 Plenum Cable B&H # COCBPQ. If your budget is constrained, go for the most affordable. If you need better quality, go for the higher priced connectors.

Q: 7. How long are these cables?

A: The cables are approximately 2 feet long.

Q: 8. Will these work with the EW IEM G4

A: Yes, the Sennheiser GA 2-XSW 2, Extension Cables and BNC Sockets to Front-Mount One Pair of Antennas will work to extend the antenna connection of the Sennheiser ew IEM G4 Wireless Monitor System's transmitter.

Q: 9. What is the operational humidity range for this?

A: The environmental humidity for the Marshall Electronics V-1055BNC 1/3-Inch CCD is listed as within 95% relative humidity. Additionally, the operating temperature is -20C to +55C or -4F to +131F.

Q: 10. What size crimp die do I need for this connector?

A: Size .187 crimp work perfect!