The DJI Transmission Module for O3 Air Unit - Compact & Reliableis a replacement for the transmission module that comes with the O3 Air Unit. An essential part of the O3 Air Unit, this module uses the DJI O3+ video transmission system to stream footage back to a pilot's DJI Goggles 2 or FPV Goggles 2 from up to 6.2 miles away. Using frequency auto-switching and the Air Unit's omnidirectional antenna (not included), the Full HD 1080p H.265 video stream is kept stable and interference-free. The module attaches to your existing camera module with a coaxial cable (not included) via a convenient quick release design.

For DJI O3 Air Unit    Works with DJI Goggles 2 & FPV Goggles 2    O3+ Video Transmission System    1080p H.265 Stream from up to 6.2 Miles    Frequency Auto-Switching    Easy Install via Quick Release Design    30ms Low Latency    50 Mb/s Maximum Bit Rate

• 30ms low latency
• 50 Mb/s maximum bit rate

Related Questions and Answers

Q: 1. Can I power this with USB C to AC adapter like the one for a Mac Book Pro?

A: No, the DJI Transmission with High-Bright Monitor Combo can receive power from the barrel, DJI WB37 LiPo Battery Pack, or adapter Sony L series NPF type battery only. The USB-C cannot receive power.

Q: 2. Can one draw the active track box from monitor with RS3 Pro?

A: Yes, DJI active track is compatible when using the DJI Ronin Image Transmitter.

Q: 3. can the receiver connect to the mac/computer so that OBS can recognize it as a video/audio source for streaming?

A: The High-Bright Remote RX Monitor does not have a video output to send a video signal.

Q: 4. Is there a sdi input?

A: The DJI High-Bright Remote Monitor (BH #DJHBRM) from the DJI Transmission with High-Bright Monitor Combo does not have an SDI input. However the DJI Wireless Video Transmitter (BH #DJVDC) which is also included in the kit does have an SDI input.

Q: 5. With the handgrips mounted on the combo can you remote control the gimbal and focus on the inspire 3?

A: The DJI Transmission Combo can both control the gimbal on the Inspire 3 as well as pull focus on the camera.

Q: 6. Is the dji transmission combo replacing the dji force .

A: The DJI DJI Transmission Combo would be similar to the DJI Force controls for the latest gimbal models. DJI has not indicated that DJI Force is being replaced.

Q: 7. Is this transmitter compatible with the Ronin RS2 gimbal?

A: The DJI Transmission Combo (B&H# DJTRC) allows for transmission (and reception) of an HDMI or SDI signal and also allows for control of only the DJI RS 3 Pro Gimbal Stabilizer (B&H# DJRS3P), at least at the time of the announcements of each product. However, you could use just the video signal transmission and reception feature with any source of HDMI or SDI and even if you are using an RS2.

Q: 8. Is 68ms latency (approx 15 frames) too much delay for pulling focus? https://fpstoms.com/

A: The latency of the Follow focus unit also needs to be considered. The DJI Transmission with High-Bright Monitor Combo is generally not considered good enough for focus pulling, in its own, regardless of the follow focuses latency.

Q: 9. Is the handgrip slots on the side of the monitor cold a cold shoe mount, where I could hold a different wireless focus handgrip?

A: The handgrip slots on the DJI Transmission with High-Bright Monitor Combo are specifically made for the DJI Ronin 4D handgrips. Using them for anything else will damage the contacts and may cause the system to fail.

Q: 10. Can the monitor be used as on-camera monitor?

A: The DJI High-Bright Remote RX Monitor that is included with the DJI Transmission with High-Bright Monitor Combo is meant to be used as an off-camera monitor, but it can also be used as an on-camera monitor.