The red CAMVATE Universal Super Clamp with Ball Head & T-Handlefrom CAMVATE Universal Super Clamp with Ball Head & T-Handleincludes a detachable ball head with a 1/4"-20 top screw and both 1/4"-20 and 3/8"-16 threads. Use this clamp for mounting a DSLR or another camera, a video light, or another accessory on a pipe, shelf, pole, or other surfaces. Constructed from aluminum, steel, and nonslip rubber pads, the Super Clamp provides a clamping range of 0.4 to 1.2" and a maximum open jaw of 2.1". The silver T-handle provides flexibility when mounting the clamp in tight spaces.

Super Clamp with 0.4 to 1.2" Clamp Range    Ball Head with 1/4"-20 Top Screw    Maximum Jaw Opening: 2.1"    4.4 lb Maximum Load Capacity    1/4"-20 & 3/8"-16 Mounting Threads    Silver T-Handle, Nonslip Rubber Pads    For Mounting DSLRs, Cameras, Accessories    Aluminum & Steel Construction

Related Questions and Answers

Q: 1. Will this fit onto a guitar ?

A: It would depend on how wide the neck of your guitar was, I tried it on a Takamine acoustic around the neck, it may interfere with the strings on the fret board, alternatively it will fit up where the string clamps and tuning thumb screws are. Hope that helps.

Q: 2. What is the weight of this part

A: The following unit weighs in at 2.5 lbs.

Q: 3. I made the mistake of purchasing a cheaper alternative and the grip head wiggles on the clamp. Is this an issue with these too?

A: When the grip head is tighten down on the Avenger D230 Super Clamp Grip Head (Black) it does not move. It is very well made.

Q: 4. Can you attach this directly to a tripod head?

A: if you purchase the Impact Short Double Female Stud for Super Clamps with 1/4"-20 & 3/8"-16 Threads, B&H # IMSRP103, you should be able to connect the Manfrotto 035RL Super Clamp with Standard Stud to the 1/4"-20 or 3/8"-16 male thread on the top of your tripod head.

Q: 5. Can I screw a leofoto magic arm directly into the clamp?

A: Yes, it fits right in using either the 5/8" female receiver or it can be screwed into a 3/8 or 1/4-20" thread if your magic arm has those options.

Q: 6. can i buy this clamp and then just the stud later if i need it?

A: Absolutely ! You can add it on afterwards !

Q: 7. Can anyone post a picture of the Super Clamp in use? I have a camera that I would like to hang high . Would this work?

A: Yes, you can easily attach a camera to this directly or attach a tripod head to the clamp (better option).

Q: 8. If this clamp's stud was oriented horizontally, parallel to a table top, could the 1/4-20 threaded end support 5-10 lbs. without it snapping off? If not, is there a stud that is made of steel that would be compatible?

A: The 1/4" thread would not be stable for an item that weighs 5-10 lbs. If you prefer to use a quick release plate, the Manfrotto 323 RC2 System Quick Release Adapter with 200PL-14 Plate, BH # MA323 screwed into the Manfrotto 037 Reversible Short Stud, with 3/8" & 1/4"-20 Threads (Brass), BH # MA037 would be better. The Short Stud should have its 3/8" thread facing towards the bottom of the quick release.

Q: 9. Would this ball also work with Ram mounts?

A: The Kupo Super Knuckle Hex Stud Ball for Convi Clamp has only been tested with the Kupo Convi Clamp. Using it with any other mount would have varied results.

Q: 10. Hi Can I attach a gimbal head to the clamp?,I want to clamp it to a shelf in a hide with gimbal head attached to mount my camera and large prime lens to.I believe the clamp can hold 30lbs is that correct?

A: You could attach a gimbal head to this clamp since it can hold up to 33 lbs. To get the head attached, you can use the Manfrotto 208HEX Head Mounting Plate with Hex Stud - 3/8 Thread B&H # MA208HEX which has a 3/8 male thread. Please see the image below for reference.