The TDA Series CATV Distribution Amplifier 5-42MHz 54-1000MHzfrom TDA Series CATV Distribution Amplifier 5-42MHz 54-1000MHzis a 1 GHz push-pull indoor broadband distribution amplifier with active return, designed for RF distribution systems in apartment complexes, hospitals, schools, and hotels. The amplifier features a 54 to 1000 MHz forward frequency range and a reverse frequency range of 5 to 42 MHZ.

The amplifier has 35 dB of forward operational gain, 18 dB reverse gain, and has a variable gain control range of -20 dB. it employs a push-pull design that features low distortion and high output. The unit is housed in an aluminum chassis designed to provide efficient heat dissipation. It includes a power adapter and will power from a 117 to 220 VAC supply.

Two-Way Apartment/House RF Amplifier    Push-Pull Amplifier for 1 GHz RF Systems    54-1000 MHz Forward, 5-42 MHz Reverse    20 dB Forward/Reverse Gain Control    Aluminum Housing for Heat Dissipation    Power Adapter Included

Related Questions and Answers

Q: 1. Can you have source 1 routed to output 1-4 and source 2 routed to output 5-8?

A: No the BZBGEAR 2x8 UHD 4K Splitter/Distribution Amplifier with CEC Turn On/Off TV will not be able to perform Matrix switcher functions. A 8x8 Matrix switcher listed below will be able to fill your needs for routing. BZBGEAR 8x8 4K UHD 18 Gb/s HDMI Matrix with Audio Extractor & ARC BH #BZUHD88M • MFR #BG-UHD-88M

Q: 2. When switching is there a delay on the output while it re-syncs? Or is it seamless and instantaneous?

A: Never mind. This unit doesn't switch. Duh.

Q: 3. I'm looking for something that will allow me to connect multiple speaker types to my mixer to monitor music productions from different speakers. I need to send audio out from the main mix on my mixer to powered studio monitors, and non powered PA speakers (the audio would go into the built in mixer that acts as the amp for the speakers and go to the speakers from there) as well as running to a stereo amp unit (connects with RCA type audio connectors, so would run 1/4 to RCA cable) that is running subwoofers? I have been warned that running powered sound into powered speakers can be bad, so that is why I am wondering if this would be a good solution for my usage. Thanks!

A: I have this unit and it works great for the intended purpose, but I don't think I would want to use it for what you have described. It probably could do the job, but it sounds as if you need a good mixer instead. All my mixers have had monitor outputs, main outputs, and an RCA line-level output for recording (often labelled tape ). It sounds as if all your needs could be met by a decent mixer with a full compliment of outputs.

Q: 4. How do I hook up my brogan car amp to my home stereo system?

A: Most automobile head units are 12 volt DC systems and not compatible with home systems which are 110-120 VAC/60 Hz. The speaker outputs are typically mismatched for the impedance of home speakers as well.

Q: 5. This hood EW-54 says it is for Canon EF-M 18-55 STM, will it fit the EFS 18-55 STM as well. I do not find in your Vello list one listed for the EFS 18-55 STM lens, only the genuine Canon.

A: No that lens hood will not fit that lens.This is a link to the one we have that works with the EFS 18-55 STM, http://bhpho.to/1e3WJ6h

Q: 6. Does this only allow me to send the same input to multiple zones or can I run two separate inputs through this to different speakers in multiple zones? I cant read what the output section says but I see the outputs all have different power considerations

A: You can send only the same mix to different zones although you can selectively turn on and off zones.

Q: 7. What is the reason for two power inputs?

A: The AVMATRIX SD1151-12G 12G-SDI 1x5 Reclocking Distribution Amplifier has two power inputs for power back up redundancy.

Q: 8. Is this compatible with the Canon 18-55mm IS II lens?

A: The Vello EW-54 Dedicated Lens Hood is only compatible with the STM lens. It is not compatible with the 18-55mm lens that does not have the STM designation or feature.

Q: 9. can this unit work on a tascam 2488 neo and if so what is the best way to connect it to the unit for the best results on all the channels?

A: The Behringer HA8000 can be connected to the Tascam 2488 NEO. The MONITOR OUTPUT would be the proper way to connect the unit.

Q: 10. What type of scaling is used for the down conversion of UHD to HD? I have a 4k camera that does a pretty crude nearest neighbor type of scaling for the HDMI output to HD. I'm looking for a better 4k to HD quality down conversion to capture 1080p 10bit 4:2:2 video from my 4k camera to an external HD recorder.

A: This DA with Scaler is really geared more towards A/V Presentation than Video Production. It may work for your needs and is a returnable item if you are not happy with hit. However a product like the Blackmagic Design Teranex AV, B&H # BLTNAV, will give you a much higher quality of Up and Down Conversion between HD and 4k.