Flic Film Quick Fixer 4L for Photographyis four liters of easy-to-use, non-hardening rapid fixer concentrate suitable for fixing both black and white negatives and paper. The fixer does not have sodium thiosulfate (hypo) and therefore does not require a hypo-cleansing agent. Water dilution ratios differ depending on usage. The bottle contains enough concentrate to fix approximately 400 rolls of film.

For Black & White Film and Paper    4 Liters of Fixer Concentrate    Fixes Approximately 400 Rolls of Film    Does Not Require Hypo-Cleansing Agent

Related Questions and Answers

Q: 1. Will I need to double batch to develop a roll of Super 8?

A: How many batches of the Flic Film ECN-2 Processing Kit for 8 Rolls (0.5L) you will need will depend how long your super 8 film is. This chemistry though is for film that had the remjet layer removed. It won't work if your super 8 film still has the remjet layer on it.

Q: 2. Does this have the anti-halation remjet layer on it?

A: Yes, Flic Film Vision3 250D Cine Film has the Remjet anti-halation backing.

Q: 3. How many exposures does this film roll have available to be shot?

A: The Flic Film Vision3 200T Cine Film (35mm Roll Film, 36 Exposures) contains 36 exposures.

Q: 4. What is the highest temperature the device can achieve and maintain?

A: The manufacture does not list the temperature the heater works with but it is for processing so the Flic Film Precision Temperature Water Bath should be fine for regulating at 68 F. But note it does not have a cooler only a heater. So if the room you are in is over 68 degrees that could be an issue.

Q: 5. What are the inside dimensions of the tank?

A: According to the manufacturer, the interior dimensions of the Flic Film Precision Temperature Water Bath are 12" (30.48 cm) long, 6.25"(15.87 cm) wide, and 4.25" (10.8 cm) deep.

Q: 6. Does the film in this particular listing have its ramjet removed?

A: When it comes to the Flic Film Vision3 500T Cine Film (35mm Roll Film, 36 Exposures), it will have a ramjet layer on the film that will need to be removed with ECN-2 prebath chemical.

Q: 7. Where do you get cine film developed?

A: B&H offes Store drop off film developing services. There are also multiple photo labs that provide this service. I would recomend reserching for ECN-2 Process photo labs near you.

Q: 8. What is the temperature range of the controller? Can it maintain 68 F, for black and white processing?

A: The manufacture does not list the temperature the heater works with but it is for processing so the Flic Film Precision Temperature Water Bath should be fine for regulating at 68 F. But note it does not have a cooler only a heater. So if the room you are in is over 68 degrees that could be an issue.

Q: 9. Is this different than a hypo clearing agent? I am going to try a residual hypo test but was informed that the test results are not reliable with a fixer remover, but they are reliable with hypo clearing.

A: You can use this in the same way as you would hypo clearing agent.

Q: 10. does this make 1 gallon?

A: Yes, you can make a gallon. Just follow the instructions on the bottle. I think you add 16 ml of NH5 to 2 quarts water, stir it, and then add water to make a gallon of stock solution. You don't have to worry about water temperature. I usually filter my water. This bottle NH5 makes about 3 gal of fixer stock solution. You use stock solution 1:1 for your tray. For example, mix 1 quart of stock solution with 1 quart of water, and use this in your tray to fix the prints. Rotate the prints in the tray about 1-3 minutes and then wash in running water.Hope this helps.Helen