The black, medium Bubblebee Spacer Cover for Windshield - Black, Mediumis a fur cover designed to slip over The Spacer Bubble windshield size medium, and fit perfectly. Made of high-quality, high-density short-haired faux-fur, it allows for optimal frequency transparency and effective wind protection when recording outdoors in light-to-medium winds.

Constructed with a sturdy leather brim, the Spacer Cover stays firmly in place when it is mounted. The inside is made of a durable polyester mix, allowing the cover to quickly and easily slide onto the Spacer Bubble base, so you can adapt to on-location changing-wind conditions in just seconds. This polyester mix is tested to ensure the most linear frequencies. When wet, place the Spacer Cover in your Spacer Bubble mesh storage bag where the fur can dry quickly and naturally.

Minimizes Light-to-Medium Wind Noise    Fits The Spacer Bubble Medium    Short-Haired/High-Density Slip-On Fur    Acoustically Transparent Design    Quick-Drying Fur

• Slides onto The Spacer Bubble when recording outdoors in light-to-medium winds
• Easily adapt to your changing surroundings when you are in the field
• Fits in your Spacer Bubble mesh storage bag so you can keep everything close by
• Slip-on fur made from Bubblebee Industries' best imitation fur (high-density of hair)
• Quick-drying fur
• Designed in Denmark by sound lovers, for sound lovers

Related Questions and Answers

Q: 1. do we put this under the bobcat or is this seperate?

A: Hi there, Nicholas: thanks very much for your question. This product is intended for use on its own (i.e. without/in place of our fur Windjammers). You can use it over the basket and then apply a Windjammer on top, but this mostly leads to reduced high frequency content, and doesn't have that much benefit in terms of additional wind protection. The HWC is a good option on its own if you need something less obtrusive than fur, or don't want to suffer as much HF loss c. 6000 Hz. That said, our fur is renowned for its high level of acoustic transparency, so the other/more important aspect to consider might be whether you intend to use your windshield in very windy conditions. For that, chose a Windjammer; for moderate winds, the HWC would perhaps be a good bet. Hope that helps! MF.

Q: 2. Will this work with Rycote Super-Blimp for NTG shotguns? https://www.bhphotovideo.com/c/product/1246580-REG/rycote_010323_super_blimp_ntg_for_rode.html

A: Although specified for another windshield with a 17-inch length, the Rycote Hi-Wind Cover 4 Windscreen for Mono Modular Windshield 4 may also work with the Rycote Super-Blimp Kit for Rode NTG & Shotgun Mics, which has a specified length of 16 inches.

Q: 3. would this be a good choice for using the sennheiser mkh8050 or neumann km 185 outdoors?

A: Yes, this windshield would be a good choice for this application. Please note that it is not designed to be fitted over the mic itself, but rather fitted over a Cyclone Windjammer such as BH #RYCWSKS.

Q: 4. Can I put the Hi-Wind Cover on the Rode Blimp and additionally add Rode Blimp Windshield(BH #ROBLIMPR) or Rode DeadWombat Windshield(BH #RODEADWOMBAT)?

A: No, the Rycote Hi-Wind Cover is designed to fit directly over the surface of the blimp and not over any additional windshields.

Q: 5. This is to be used without the dead cat? Or over it? If it's to be used without the dead cat, is it supposed to be better?

A: The Rycote 022524 Hi-Wind Cover for Rode Blimp is designed to fit directly over the windshield basket, without another windshield underneath.

Q: 6. Which size would fit a Canon R6ii with a 100-400 lens?

A: yes, the RucPac Camera Rain Cover (Black, Medium) will cover the Canon EOS R6 Mark II Mirrorless Camera, with the Canon RF 100-400mm f/5.6-8 IS USM Lens. The rain cover will fit cameras, and lenses up to 14'' long. When the lens is fully extended, the camera and lens have a total lenght of 12''.

Q: 7. What size is best for the Sony FX6?

A: The RucPac Camera Rain Cover comes in small, medium, and large sizes, and the size would be based on the lenses you work with. The medium size would work with most setups though. Sizing (camera and lens hood total length); S 5-20cm, M 20-35cm, L 35-50cm

Q: 8. Can this Windbreaker be used with the Rycote Super-Blimp Kit for Rode NTG?

A: The Bubblebee Industries The Windbreaker for Rycote Modular Windshield WS 4 Kit is built specifically for the Rycote Modular Windshield WS 4 Kit system. It is not meant to be used with other windshield systems, and compatibility is not guaranteed.

Q: 9. Is this compatible with Sennheiser MKH-50?

A: Yes, the Bubblebee Industries The Short-Haired Spacer Cover for The Spacer Bubble Windshield (Green, Extra-Small) will fit over the Bubblebee Industries The Spacer Bubble Windshield (Extra-Small/Big Mount), which is the compatible size for the Sennheiser MKH 50 Microphone. The Short-Haired Spacer Cover is not intended to be used by itself. It is intended for use over the Spacer Bubble Windshield. You can purchase both items together, which is the Bubblebee Industries The Spacer Bubble Windshield & Fur Cover System for Shotgun Mics (Chroma Key Green, Extra-Small/Big Mount) - B&H # BUBBISBGRXSB.

Q: 10. What is the length of the item?

A: The manufacturer has provided dimensions for the inside depth of the Bubblebee Industries The Spacer Bubble Windshield & Fur Cover System for Small-Diaphragm Mics (Extra-Small) which is 2.2" (55mm). It can be used with microphones that have a diameter of 0.7 to 0.9" (18 to 24mm).