The quick release Kupo V-Lock Set with Extension Handle - Blackfrom Kupo V-Lock Set with Extension Handle - Blackincludes the V-Lock wedge and V-Lock base. The V-Lock wedge attaches with the supplied screws to a standard V-mount battery or any device that comes with 1/4"-20 or 3/8"-16 hole. The V-Lock base attaches to a Convi Clamp with the included screws. Two 3/8"-16 tapped holes on the back of the base are spaced 1" (center-to-center) to allow you to mount the base on any standard cheese plate. The extension handle comes with 1/4"-20 male thread and screws into the knob allowing for a 1" extension.

Made of Aluminum and Steel    Two 3/8"-16 Tapped Holes on the Back    Attaches to Convi Clamp    Quick Release

This quick release mounting set is ideal for a V-mount battery or any device that has a 1/4"-20 or 3/8"-16 hole

Two 3/8"-16 tapped holes on the back of the base are spaced 1" (center-to-center) allowing for the base to be mounted onto any standard cheese plate

The V-Lock base attaches to a Convi Clamp with the included screws

Related Questions and Answers

Q: 1. This Kupo Baby Stand Extension (4.2 ') can be used on the Kupo Slider Stand (45.3 ")..?

A: Being that this extension has a female 5/8" receiver and the Kupo Slider Stand has a female 1 1/8" receiver, you will need a pin such as the Impact CA-106 Junior to Baby Pin Adapter, B&H # IMCA106 to connect the two. https://bhpho.to/3gVWIu4

Q: 2. How much weigh can this extender take?

A: The weight capacity would be dependent on the stand that the extension is used with.

Q: 3. If this extension is used to connect a tether table to a runway stand base, will the setup be sturdy enough to use a laptop safely or will the whole thing be too wobbly?

A: It would depend on how you attached it but it could work if you want your laptop 2 feet off the ground.

Q: 4. How much does the entire package weights?

A: The Kupo Apple Box Set (4) BH #KUKG070412 weights about 28lbs.

Q: 5. Does this have a spigot at the top to attach a ball head?

A: We suggest the following for a better support/platform . Impact BHE-104 Camera Platform for Flex Arm B&H # IMBHE104 MFR # BHE-104 https://bhpho.to/3nEq2Lc

Q: 6. Is it really sure that this Kupo 3-Section Extension Pole is not compatible with the Kupo Slider Stand (Black, 45.3 ") + Kupo Baby Ball Head Adapter ..?

A: Hi Daniel, The Kupo Slider Stand top has a junior receiver i.e. female 1-1/8inch; The Extension Pole ends are threaded 3/8” - male on one end female on the other. The Kupo Baby Ball Head Adapter would allow the 3-Section Extension Pole to be connected to the Kupo Slider Stand. You would just need to remove the t-handle from the Ball Head Adapter so it drops into the stand top opening, and then screw on the Extension Pole https://www.bhphotovideo.com/c/product/1244788-REG/kupo_kg014212_baby_ball_head_adapter.html

Q: 7. What is the maximum load weight?

A: The Kupo 3-Section Extension Pole BH #KUKG092411 does not have a load limit listed. It is designed for light weight ballheads and cameras.

Q: 8. Will this work to hold a remote on a Canon 5D Mark2?

A: Yes. It connects to the strap holder of the camera which is the same on most Canon models.

Q: 9. how many jerkstooper comes in the box?

A: This listing is for a single jerkstopper.

Q: 10. What size/thread is the hole in the top (male) baby stud?

A: It is not threaded.