Connect your Bolt 6K or 4K transmitter or receiver to an Antenna Array with this 3.9" RP-SMA Female to RP-SMA Female Cable 3.9"from Teradek. This is a single cable that connects to one of the RP-SMA connectors on your TX or RX unit, and the other end connects to one of the panel connectors.

For Teradek Wireless Antenna Array    Male RP-SMA Connectors on Both Ends    Cable Measures 3.9" in Length    Extend Transmitter or Receiver Signal

Related Questions and Answers

Q: 1. Is this compatible with sennheiser G4 ?

A: Yes the PSC RF Multi SMA is compatible with diversity receivers in the 470-960 MHz. The Sennheiser G4 receiver is a diversity receiver.

Q: 2. Hi! I would be deeply grateful if anyone knew if this screw could be used with the Manfrotto 504PLONG plate and not interfere? I notice there is this version, and one that is shorter, but I don't want my cameras hanging on by a single thread...

A: Hi, I bought this D-ring about six months ago thinking I would be able to switch between plates and move my camera from my tripod to my gimbal quickly. Unfortunately the head on this D-ring was to thick and wouldn't give me enough clearance between the plate and the tripod head. This was just my experience with this product. Maybe you'll have better luck. I was also using the 504 long.

Q: 3. hi is this 900Hz？

A: 470-900Mhz

Q: 4. Would work on a Sony Venice 1 Rialto set up? I need to get power from the 24v output to 12v accessories like a monitor


A: We haven’t tested this, but in theory this should work. The Rialto has a Fischer 3-pin 24v output and the Hawk-Woods RP-A3 would convert the 24v to 2x 12v 2 pin LEMOs output to power the monitor. Also, as long as you are not powering off other equipment, we don’t see you running into any issue. If you need to power other accessories then, we would recommend a Battery plate with power distribution like the Tilta Cage for Sony VENICE Rialto Extension (V-Mount) for example. Tilta Cage for Sony VENICE Rialto Extension (V-Mount) BH #TIESRT13RCCV

Q: 5. Can you use the D-ring to attach a strap to carry the camera/lens? I can't find anywhere that the D-ring was designed to take that sort of load (in my case, around 8lbs). Yet I did see someone that was using the D-ring for a carry strap attachment point.

A: I assume you are talking about something like a Black Rapid Shoulder strap and attaching that via the D-ring on the Quick Release plate. I certainly would not. But, I do not leave my quick release plate attached to the bottom of any of my three Nikon bodies unless I am shooting night photography and will need my tripod on a constant basis. And, in that case, I would remove my black rapid strap which screws into that base hole via it's own device. If you have not already purchased a strap, that would attach to the base, I suggest you buy the Black Rapid strap. Worth the money and if you have multiple bodies, that strap allows you to have across your body, two cameras without any around your neck or banging into one another. In addition, it makes shooting and hiking, etc. so easy.

Q: 6. how to set up with wisycom mcr42s?

A: thank you for your question. please give us a call at 800.606.6969 so that we can better assist you/

Q: 7. Can I use the Induro PU-50 Slide-In Quick Release Plate with this D screw?

A: This screw can only be used with Oben RP plates.

Q: 8. What is the length of the stem (threaded & unthreaded portion from tip to underside/shoulder of the head)? QRS-14D = 7.5 mm (from Q on its page) RPS-14D = ? mm

A: The length of the threaded portion of the Oben 1/4"-20 Screw with D-Ring for RP Plates is 7.1mm, whereas the length of the unthreaded portion is 4.3mm.

Q: 9. What is the size of the Plate?

A: 50mmx47mm,and it is compatible with Giottos head and ball head

Q: 10. What is the purpose of the retractable video pin ?

A: It is to lock the plate in and keep it from spinning around