When you're on a busy set and need to change settings for a Bolt 6 LT wireless setup for your monitors, it may get confusing which one is which when there are so many wireless setups. Teradek Color Band Bolt 6 LT RX Redhas devised a clever way of identifying your synced transmitter and receiver set with this red Teradek Color Band Bolt 6 LT RX Redto wrap around your receiver to match its partner on the other end. This flexible red silicone band wraps around the Bolt 6 LT receiver and allows you to see the color of the unit and find its paired device.

ID Synced RX/TX Pairs on a Busy Set    Designed for Sets with Many Monitors    Fits Around Bolt 6 LT RX    Flexible Silicone Band    Comes in Red Color

Related Questions and Answers

Q: 1. can the V Mount plate be easily removed for use without it?

A: The V-Mount battery plate can be removed on the Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless Receiver (V-Mount).

Q: 2. If the Tx is fed signal via HDMI, will the local BNC loop thru / output transcode that signal lien the older 500 units did?

A: Yes, the Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless Transmitter supports HDMI cross conversion. This would allow the HDMI input to output through the 3G-SDI. The Teradek Bolt 6 also would downscale 4k signals from HDMI to HD when outputting via the 3D-SDI.

Q: 3. I heard there will be a delay from a 4k signal to a 1080 monitor. Is there a way to send a 1080 signal to a monitor?

A: If your camera is set to output a 1080p signal, the Teradek Bolt 6 LT 750 3G-SDI/HDMI Transmitter/Receiver Kit will transmit and receive that same signal.

Q: 4. Can I use more than one tx / rx pair in the same environment?

A: It should theoretically be possible to use 6 Teradek Bolt 6 LT HDMI 750 Transmitter/Receiver Kits in a single location if you are all using fixed frequencies and there is minimal external interference in the area. The spacing of the equipment will also be incredibly important. With the Bolt 6 you'll want to have at least 10 feet between the transmitter and the receiver, and between other sets. If more receivers are used in a set this will impact the communication even more so. The Bolts operate in the unlicensed 5 GHz spectrum which can be use by other devices like WiFi routers, other wireless transmitting systems, etc. Here is an article that may be helpful: https://support.cs.inc/s/article/Bolt-4k-Best-Practices-for-Interference

Q: 5. Can the Bolt 6 Receiver HDMI receives signal from from a Bolt 6 SDI/HDMI version?

A: The Teradek Bolt 6 LT HDMI 750 Wireless Receiver can receive the signal of any bolt 4K series transmitter, including the transmitters that SDI/HDMI inputs.

Q: 6. How can this transmitter be mounted to a camera rig?

A: The Teradek Bolt 6 LT 750 Wireless Transmitter has mounting points on the bottom of the transmitter to attach to different points.

Q: 7. how far is 750 distance in meter can reach?

A: The Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless RX/TX Deluxe Kit (V-Mount) can transmit up to 228.6 meters line of sight.

Q: 8. Does the kit come with a hard case? Thanks.

A: Yes, the Teradek Bolt 6 LT HDMI 750 transmitter/receiver it comes in a hard case.

Q: 9. Hello, will this fit the new Teradek 6 LT series either the 1500 & 750 receivers?

A: No, the Teradek Bolt 1000 LT and 500 XT RX Battery Plate will not support the Teradek 6 LT. Please work with the plates listed below. The plates below will work with the 1500, and 750 Transmitter, or Receiver. Female Battery side V-mount: Teradek Single-Battery Plate for Bolt (Female, V-Mount) BH #TE110854 Male Camera side: Teradek V-Mount Battery Plate for Bolt 4K Monitor Module (Male, Camera Side) BH #TE110855

Q: 10. can you transmit too 3 receivers?

A: The Teradek Bolt 6 LT HDMI 750 Transmitter/Receiver Kit is a 1 to 1 system only.