The Videotel Digital HyperSound Power Amplifier - Blackamplifies your audio signal for use with the HyperSound system. This black amplifier is small enough to hide out of the way and sleek enough to fit into almost any environment, such as schools, retail, banks, and more.

Frequency Response: 300 Hz to 18 kHz    Max Audio SPL: 100 dB @ 1.5 kHz and 6.5'    Power Supply Outputs 30 VDC    Supports Worldwide AC power Input

Related Questions and Answers

Q: 1. My speakers are rated max 380 watts RMS,is the PX5 too powerful to power my fronts?

A: No. Not too powerful. As long as the speakers are 8 ohm. 500 Watt amp is a good match for 380W speakers.

Q: 2. I wish to use this amp with (4) speakers inside a small (1,500 sqft) fun center lobby with 10ft. ceilings. Would someone be able to suggest a good speaker match? Thanx.

A: Thank you for your question. Please give us a call at 800.606.6969 so that we can better assist you in getting the right speakers for your needs.

Q: 3. Will this work with a Audio Technic U855QL podium microphone, (Dynamic)?

A: The Pyle Pro PCAU25A 80W Stereo Power Amplifier BH #PYPCAU25A does not have a microphone input.

Q: 4. My speakers are Max 380 watts RMS, is the PX5 too powerful?

A: No, the PX5 is not too powerful for speakers that can handle 380 watts each. You can use an amplifier with a power rating that is up to double the amount of power that the speakers are rated for at the same impedance. For example, if your speakers are rated for 380 watts at 8 ohms and the PX5 is rated at 500 watts per channel at 8 ohms, they are compatible.

Q: 5. how do i set the jumpers in back i cant understand the diagram on the back?

A: The jumper settings on the ISA Ti will depend on the mode you are using the amplifier. Switch 1&2 correspond to the limiter and filter for channel 1, switch 9&10 correspond to the filter and limiter on channel 2. The center switches (3-8) set the amplifier mode: Stereo parallel or Bridged. Settings are shown on the rear panel diagram. If you are still having issues please contact a Pro Audio Rep here for assistance at 800-606-6969, or email a href= http://audio@bandh.com target= _blank audio@bandh.com/a

Q: 6. hello it can be connected to a voltage 220?

A: The QSC GX3 operates at 120V AC. You will need to use a step-down transformer to use it with 220V AC such as the Sevenstar ST-500 Step Up/Step Down Transformer - 500W (B&H # SEST500UD) or Watson Voltage Converter - 500 Watt Max (B&H # WAVCGSD500).

Q: 7. just how good is this amp? give me a comparison .

A: This model is known for its very low self noise and high signal to noise ratio using Benchmark's DAC3 digital to analog converter. It is also known for its ability to output at higher levels without introducing distortion into the signal. Further details can be found on the AHB2 product page on Benchmark's site, linked here: https://benchmarkmedia.com/products/benchmark-ahb2-power-amplifier

Q: 8. Speakers ratings, should I take minimum or peak as reference to match my speakers to an amplifier?

A: You should take both ratings into consideration if they are provided. RMS power ratings provide a better idea of the continuous power that is provided by an amplifier or when an RMS rating is listed for a speaker, it is the amount of continuous power that a speaker can handle. Peak power ratings refer to occasional short bursts of power that an amp can provide or the amount of power in a short burst that a speaker can handle. When only peak power ratings are provided, you can determine the RMS power rating by multiplying peak power x 0.7071. For example, if an amplifier is rated at 800 watts peak power, multiply 800 x 0.7071 which equals 565.68, meaning the amp's RMS power is approximately 566 watts.

Q: 9. Im frm Philippines.. What is the right wattage/amperes of transformer be use to power this Gx3

A: You would need a step down transformer such as this BH #SEST1500UD.

Q: 10. What is the factory warranty for the PX8?

A: The Yamaha PX8 Stereo Power Amplifier has a three year limited warranty.