Add a powerful but compact, high-power linear RF amplifier to your test platform with this Wideband 1W Microwave Amplifier 40MHz-10GHz RF-Linksfrom RF-Links. The aluminum amplifier has been designed for research, military communications, and laboratory testing applications, and it provides 50-ohm RF input and output, over 50 dB typical gain, and up to 1W RF power output. It supports transmitters in the 40 MHz to 10 GHz broadband frequency range. This unit features SMA female input and output and it requires a separately available 12V power supply.

High-Power Linear RF Amplifier    For Lab and Research Applications    1W Power Output, 50 dB Gain    40 MHz-10 GHz Frequency Range    50 Ohms RF Input/Output, SMA Female    For Government Agency Use, No Export

Ideal for telecom, government, fiber, military, and research laboratory testing applications

10 MHz to 10 GHz frequency range

1W output power

Compact, lightweight, rugged, and reliable

50-ohm input/output impedance

Requires 12V power supply

Related Questions and Answers

Q: 1. Will this work for the Sony A73 original strap in that camera?

A: Yes. The following anchor set will work with the Sony a7 III Mirrorless Cameras.

Q: 2. Is compatible with the SLX-D too?

A: Yes, the Shure UA844+SWB/LC Wideband Antenna Distribution System is compatible for use with Shure SLX-D receivers.

Q: 3. Are these V3 or V4 anchors?

A: We are still working through some stock on our straps that have V3's. These Anchor Links still might come with V3's, and if you do, they can always be replaced through our Anchor Update Program here: a href= https://support.peakdesign.com/hc/en-us/articles/360000833866-2018-Anchor-Update target= _blank https://support.peakdesign.com/hc/en-us/articles/360000833866-2018-Anchor-Update/a

Q: 4. How many anchors and lugs come in this item?

A: The B&H overview for this item states: "Two Links for the strap are included, as are four Anchors that attach to your camera."

Q: 5. i want use this for ski and cruise ,do i need any license?

A: No a license is not required. This was used to communicate during a large convention at a resort hotel.

Q: 6. The bottem of the connector strap opening for wider strap ? Like Nikon Z 800 mm /f6.3 lens will fit ? Thanks

A: The Peak Design AL-4 Anchor Links are compatible with the Nikon LN-3 strap for the Nikon NIKKOR Z 800mm f/6.3 VR S Lens.

Q: 7. Are the anchors strong enough to carry a Z9 attached to a 400 F2.8 lens?

A: Each anchor can withstand over 200 lbs of force so it will easily support a large camera and lens such as the Nikon Z9 and the 400mm f2.8 lens.

Q: 8. How wide? Can I use 1" webbing or only 3/4"? What is the difference btw V3 and V4? How can I identify the diff on box?

A: Peak Design AL-4 Anchor Links housing has 2 holes. the smallest one is 1.2 x .32 cm, the largest is 32 x .32 cm. Therefore any webbing would fit through them. The V4 has a thick cord and the logo is only in one side compare to the V3 anchors.

Q: 9. Does this product come with BNC antenna cables or just the antennas?

A: Yes. see below: In the Box Shure UA844+SWB UHF Wideband Antenna Distribution System (470 to 960 MHz) PS45 Power Supply 4 x Locking DC Power Cables (for ULX4D, ULXP4) 4 x Non-Locking DC Power Cables (for QLXD4, SLX4, and BLX4R) 10 x 22" BNC Cables 2 x 6' BNC Cables 2 x Bulkhead Adapters Rackmount Hardware Kit Limited 2-Year Warranty 2 x Shure UA874 Active Directional Antenna 2-Year Limited Warranty

Q: 10. can they be used with optech's camera straps?

A: Yes, we suggest the following strap for such a application. OP/TECH USA E-Z Comfort Strap (Black) BH #OPSEZCB • MFR #2701252 https://www.bhphotovideo.com/c/product/118815-REG/OP_TECH_USA_2701252_E_Z_Comfort_Strap_Black.html