[Yes] Needed to replace a wireless router with this router. Love the smaller footprint as it adds room in my network box.

[4 GB DDR4] I've been waiting for an affordable rack-mount 10Gbps router from a reputable company, and it's finally here!

I'm using this router for a 10Gbps internet connection. I'm getting around 8200 Mbps throughput, which is around the same as what I get if I connect my PC directly to my ONT. Unlike some other competing products, TP-Link's hardware is sufficient to actually handle these fast speeds.

My internet provider (Sonic) use copper 10GBase-T (standard Ethernet cables) for their ONT, so I'm using a Wiitek SFP-10G-T module in the WAN SFP+ port. The other SFP+ port goes to a MikroTik CRS312-4C+8XG 10Gbps switch that my devices are plugged in to.

I haven't tested many of the built-in features yet, including the Omada controller. I don't really need any fancy features - I was upgrading from a basic consumer-grade wifi router, so honestly any router would have been fine for me. You don't have to use an Omada controller, especially if you just have one TP-Link device to administer, as the router has a decent web UI built-in.

One of the main downsides of this router is that the eight Ethernet ports are only Gigabit. I really wish TP-Link would have at least made these 2.5Gbps ports. I guess they had to limit them to Gigabit to reach their $350 price point, but I would have been happy to pay a bit more to get 2.5Gbps. Having said that, Gigabit is still plenty of bandwidth for many devices, and you still get the full throughput across all the ports (each one can be concurrently downloading at 1Gbps, using ~8Gbps upstream bandwidth). If you want to get 2.5Gbps or 10Gbps on downstream devices, I'd recommend also buying a 2.5Gbps or 10Gbps switch that has an 10Gbps SFP+ uplink, and connect it to the SFP+ LAN port on the ER8411 via a DAC cable.

[230 MB] Probably overkill for my currently 4 AP wifi mesh home network, but i also used this with the omada vpn router and a poe switch for a quick and seemless install and making the IT folks that i know drop their jaws with the network topography map this gives. I wish the floorplan allowed you to enter a scale and then show wifi AP coverage just for giggles, but what it has is also really cool just to look at if you have a floorplan to upload.

[Internal] This was an excellent choice to replace an older VPN appliance and use more modern cryptographic standards. The web user interface was easy to use to configure for my network and VPN tunnel.

[Yes] TP-Link ER605 V2 Omada Gigabit VPN Router was easy to set up (using it as a standalone router) and basically started working once powered on. The boot cycle is a bit slow (~2-3 mins), but once active there are no issues with all the network devices connected to it.


The 4 ports are sufficient for setting up 4 different networks and the streaming devices seem to be more stable (less buffering, more responsive) than before. I should have bought this router years ago.

[230 MB] I bought a couple of Omada access points and this does a great job managing them. The UI looks good and the information provided is helpful. The mobile app that connects to it works fine as well.

[8.415 lb] This is intended for IT people and states so in the manual but it does have a quick setup mode which get you up and running very easily and quickly. I am not familiar with this type of equipment so there is a steep learning curve, but that's my problem, I bought it with my eyes open. In looking through the settings it seems to have just about everything you might want to configure for your needs. So far I am happy with the unit.

[4 GB DDR4] This TP-Link ER7206 router was purchased to replace an ancient D-Link DGL-4100 router that still worked but which no longer maintained full throughput and which didn't support IPv6. Both of these routers have built-in 4-port Ethernet switches.

When it comes to Ethernet routers, my needs are quite simple and the ER7206 meets those needs perfectly. So far it seems to be performing flawlessly.

The router is being fed by a cable modem (550 Mbps downstream and 22 Mbps upstream) and has a computer, color laser printer, smart TV, and Wi-Fi Access Point (AP) connected to it. The AP has a built-in 4-port switch to which a Blu-ray Disc player is connected.

The router was directly connected to a computer for setup purposes and the process was straightforward. I did update the firmware, which is always a good idea since some fixes may be security related.

If your needs are as simplistic as mine, then I highly recommend that you consider this product.

[Internal] Thank you, Now I can make my own quest wifi

[230 MB] this team tp link ER8411...it is a brutal team.... perhaps there is no other manufacturer that offers so many features and is open to the future... it is an exceptional team.. greetings my people from B & h