The Cinema Devices Ergorig Lightweight Body-Mounted Harnessfrom Cinema Devices Ergorig Lightweight Body-Mounted Harnessis an innovative body vest for shoulder-mounting a camera without putting any stress on the spine. It supports heavy-duty loads, such as a fully-accessorized ARRI ALEXA 65, and 100% of the weight is distributed to the hips. This standard version is designed for operators with an average-length torso (see more about this below).

The Ergorig features a robust shoulder rest that sits slightly elevated off your shoulder, and you place your camera rig right on top of it. At the same time, because the Ergorig belt secures above your hips, all the weight of the camera load is displaced to the hips, so there's no pressure at all on your spine.

You do feel some contact with the shoulder rest, just a touch, especially as you move about, and this helps have optimal control of the camera. You can alternatively float the shoulder rest a bit higher so there's no contact at all. The Ergorig was developed by a veteran camera operator over a period of about two years, with consultation from an orthopedic surgeon. It transfers all the weight from the thoracic/lumbar vertebrae to the hips.

Because the Ergorig sits above your waist you can freely sit, kneel, run, and otherwise move around with your camera load, and there will be no change in pressure on your spine. The shoulder rest is large and is designed to ensure that the camera won't slide off of it. It sits level, unrelated to your shoulder slope. It also has a non-stick surface to ensure a smooth workflow. The tilt angle and lateral position of the shoulder rest are also adjustable after loosening four screws. And the height of the Ergorig is adjustable along the strut to better adjust to your torso. The Ergorig also has accessory loops for walkie-talkies and other on-set accessories.

This standard version of the Ergorig is designed for the majority of operators. The difference between the standard and short versions is in the length of the struts and is based on the operator's torso. Measure your torso from your front hip point to the top middle of your shoulder. If the length is over 21", the standard version is for you. The belt size is the same in both versions and is adjustable to fit most operators. (If you're right at 21", either version will work for you.) The Ergorig is suitable for men and women operators alike. Women may prefer to adjust the midriff strap, which stabilizes the rig to the body, either above or below the chest line, or to set it to sit straight across.

The Ergorig also supports a camera in underslung mode. To do this, attach any secure strap to an eyelet of the camera's top handle, and wrap it around the gripping pad on top of the Ergorig. The Ergorig will support the weight, and the midriff straps will keep everything in place. For transport, the Ergorig can be broken down in order to pack in a more compact form. After removal of several screws, the different parts of the Ergorig can be removed from one another. And everything packs away into an included carry bag.

For Extended Handheld Shooting    Ergorig Standard Harness    Undersling Suspension System    6" Riser for Suspension System

• Shoulder-mount a camera without putting any stress on the spine
• Robust shoulder rest keeps your camera slightly elevated off your shoulder
• With the Ergorig belt secured above the hips, 100% of the weight is transferred off the shoulder and thoracic/lumbar vertebrae to the hips
• Supports heavy-duty loads, such as a fully-accessorized ARRI ALEXA 65
• Although the shoulder rest sits slightly raised, you do feel some contact with it (or you can set it higher so there is no contact)
• Designed not to restrict movement, so you can freely sit, kneel, run, and otherwise move around with your camera load
• Supports a camera in underslung mode (a secure strap is required for this)
• Suitable for men and women operators alike
• Accessory loops for walkie-talkies and other on-set accessories
• Breaks down for transport
• Made in the USA

Related Questions and Answers

Q: 1. What is the height limit? Asking at I am 6’6”.

A: Cinema Devices says that it works with all body sizes. Also - What size should I get? Measure from your front hip point to the top middle of your shoulder. If you're less than 20" order a small. Your front hip point is the part that feels like the tip of the triangle in your hip on the front side that is right around your belt line. If you would like us to check further with CD send us an email request to - provideo@bhphotovideo.com

Q: 2. Hello, I am wondering if I can fit the Impact Wall Plate(a href= http://www.bhphotovideo.com/c/product/841117-REG/impact_srp_123_wall_plate_with_5_8.html target= _blank http://www.bhphotovideo.com/c/product/841117-REG/impact_srp_123_wall_plate_with_5_8.html/a) in front of this body harness. There's 4 holes in front but do they match and if the thread size are the same?

A: This item was just announced and listed on our website. Unfortunately at this time we do not have any more information regarding the exact specs. Please keep an eye on our website for updates as more details are listed.

Q: 3. How far apart are the front 1/4 20 threads (horizontally)?

A: We do not have this measurement. Please contact the manufacturer directly: CONTACT INFOMATION:ADD:1619 Glide Gear Executive Ave. Myrtle Beach SC 29577TEL: (843) 945 4031EMAIL: contact@glidegear.netHOURS: Mon Fri: 9:00AM 5:00PM EST

Q: 4. Can someone who owns this run blackmagic disk speed test on it and post the results?

A: Unfortunately we are not set up to do tests like this, but perhaps you could contact the manufacturer for more in-depth specifications and testing.

Q: 5. Is this MLC or SLC?

A: This memory card is built with MLC.

Q: 6. What is real speed of this card by CristalDiskMark ?

A: Yes perfect

Q: 7. Has anyone tried it on the Blackmagic Pocket Cinema Camera 4K?

A: This card is not on Blackmagic's approved list of CFast 2.0 cards for use with the Pocket Cinema Camera 4K at this time.

Q: 8. Can you remove the back plate?

A: Unfortunately no. The Glide Gear Medusa Body Harness back plate can not be removed.

Q: 9. When is this coming?

A: Sorry, but we do not have a definite date of availability for this product. Please monitor the product page and request a stock alert if available.

Q: 10. Has anyone try it & Is it reliable like the Sandisk & Lexar?

A: This card is backed by a limited lifetime warranty.