The Hard Case for PTZOptics Cameras and G4 Controller from Jason Cases is a genuine Pelican 1650 case made of ultra-high-impact structural copolymer material with a laser-cut, high-grade foam interior that is custom cut to fit three PTZOptics cameras and a G4 PTZ controller. The case is watertight up to 30' and has a built-in automatic purge valve. It features locking latches and can accept padlocks for added security.

Genuine Pelican 1650 Case    High-Impact Copolymer Material    Watertight to 30'    Built-In Automatic Purge Valve    Laser-Cut High-Grade Foam Interior

The case stores the following items:

• Three PTZOptics PTZ cameras
• PTZOptics Joystick G4 PTZ camera controller
• Cables and power cords
• Multiple accessories

Related Questions and Answers

Q: 1. Will this control a Sony BRC-X1000? Will it provide all the focus/zoom/iris/pan/tilt functions that a Sony controller does?

A: It will offer control via VISCA protocol same as SONY. Features may differ from actual and specific SONY controllers.

Q: 2. what is the maximum focal length of the camera?

A: PTZOptics Move 4K SDI/HDMI/USB/IP PTZ Camera (BH #PT20X4KGYG3) has focal length of 6.2- 125mm. The camera also has 20x optical zoom and 16x digital zoom.

Q: 3. Does this system require a computer to operate or does it contain its own operating software?

A: A computer is not required when controlling the PTZOptics Producer-SE Camera & Controller Bundle. However, a computer would be needed to view the camera's setup menu and make installation and setup less difficult. A POE switch for power and connecting all the gear and Cat 6 cables would be required. Netgear 8-Port Gigabit Ethernet PoE+ Unmanaged Switch BH #NEGS108PP1NA Comprehensive CAT6a Shielded Patch Cable (100', Blue Finish) BH #COCAT6A100BU • MFR #CAT6A-100BLU

Q: 4. Will this output a 4K stream for live streaming?

A: Yes, the cameras in the kit of the PTZOptics Producer-4K Camera & Controller Bundle (Gray) will produce up to 4K60p from the HDMI for live streaming.

Q: 5. I'm new to this. How do I hook up more than one camera by using POE. I only see one port on the controller and one the camera. Is there some sort of hub I need to get?

A: The cameras would be connected with a POE powered network switch, such as an Ubiquiti Networks US-8-60W, and the controller will also be connected to the same network switch and that is where the communication between the cameras and the controller will occur. https://www.bhphotovideo.com/c/product/1296866-REG/ubiquiti_networks_us_8_60w_unifi_8_port_gigabit.html

Q: 6. WIll the RJ45 act as a control cable as well as the camera feed? If so, how do i get the signal from the controller to my encoder?

A: While this controller does not accept a video signal the cameras it works with usually will be able to send video through IP over the Ethernet cable.

Q: 7. Can I save a zoom IN or OUT as a preset?

A: The presets can set zoom in or zoom out functions as well as positioning.

Q: 8. Would this work with daisy chaining to a BlackMagic ATEM M/E Advanced Panel?

A: This cannot be daisy chained to an ATEM Panel.

Q: 9. Does this system have to be connected to the network to operate all three cameras?

A: The PTZOptics PT-JOY-G4 IP/Serial Joystick Controller (4th Generation) included in the PTZOptics Producer-SE Camera & Controller Bundle (Gray) would need to be connected to the same Ethernet network as each PTZOptics Move SE SDI/HDMI/USB/IP PTZ Camera with 20x Optical Zoom (Gray) in order to control the cameras via IP. The controller can also be connected via serial RS-232 and daisy chained between the cameras for control via serial as well.

Q: 10. Looking for a hard case with wheel that will fit the Phantom 3 kit with the prop guards. Question, will the drone fit in this case with the guard props on (without taking it off from the drone)?

A: no