Representing a new generation of dynamic processors that can appeal both to skilled users and those with limited time, the DL241 Auto Compressor from Drawmer is a dual-channel compressor with comprehensive auto-program features and dual-mono or stereo linked operation. Sporting a program adaptive gate/expander circuit as well as a sophisticated, automatic soft-knee compression circuit, the DL241 makes it easy to accommodate any signal or usage scenario without compromising control, as each section also features manual override and variable control over functions like attack, release, and ratio.

Adjustable peak levels allow you to avoid excessive peaks and unpleasant distortion through Zero Response Time, Zero Overshoot circuitry, and the input levels can also be adjusted, from +4 to -10 dB. With the bright LED meters, you can easily view your levels at a glance. This unit includes an AC power cord for immediate use.

For Broadcast, Live Sound, and Recording    Program Adaptive Gate/Expander    Auto Soft-Knee Compressor Circuit    Variable Manual Control on All Sections    Adjustable Peak Level    Comprehensive LED Meters    Stereo-Link or Dual-Mono Operation    Hard-Wired Bypass    +4 or -10 dB Input Selection    Includes AC Power Cord

Comprehensive LED meters give at-a-glance indications of gain reduction, and input/output signal level gain reduction from 1 to -30 dB is shown simultaneously with signal level from 20 to +15 dB. Other single LEDs indicate function status of gating action, auto mode, bypass, peak limiting, stereo linking, and power on.

Zero Response Time, Zero Overshoot circuitry provides an absolute limit to the peak level of the output signal, adjustable from 0 to +16 dB above system level. When set to the required level, any excessive peaks will be stopped and the gain will be momentarily decreased if necessary.

The Zero Response Time is essential to avoid unpleasant distortion when mastering for CD or sending any signal to digital equipment. Zero Response Time means that the DL241 provides complete protection from even the fastest and shortest signal spikes (overloads), making the unit also ideally suited for speaker system protection in sound reinforcement applications.

A fully balanced hard-wire bypass connects the input directly to the output allowing the signal to pass through the unit with no power applied. In bypass, the VU level meter displays the input signal.

Related Questions and Answers

Q: 1. Is this transformer based? Does this not allow phantom power to pass though?

A: No, the Kopul HMX-2 Humbuster - Dual-Channel Hum Eliminator with XLR and 1/4" Connectors is a passive device that does not pass phantom power. It is not intended for microphone use, it is to be used with instrument or line level devices.

Q: 2. What voltage are the various units requiring. ie to use a battery pack where there i s no power. ?

A: This specification is not specified by the manufacturer. Please contact PIXIO directly for additional details: ccc@movensee.com

Q: 3. Will this card input both HDMI channels at the same time?

A: I have the Quad, which is essentially the same thing, and we use it to live-stream 4 simultaneous cameras. So, using that assumption, it'll do so very very well. Very happy with ours.

Q: 4. How long does it run on battery power? My battery runs out very quickly, after 1-2 hours((

A: https://www.bhphotovideo.com/c/product/1460331-REG/comica_audio_cvm_ax3_dual_channel_xlr_audio_mixer.html/specs Comica Audio CVM-AX3 Specs Battery Life Phantom Power Off: Up to 40 Hours Phantom Power On: Up to 6 Hours

Q: 5. Does this work with Laptop output capture into this card?

A: If your laptop has a PCIe x4 (PCIe 2.0) slot in it, or if you use a PCI chassis with support for a PCIe x4 (PCIe 2.0), the Magewell Pro Capture Dual HDMI Card (2 Channel), would be able to work.

Q: 6. what is channel A B C D ?

A: Channel A,B,C or D refers the the frequency the mixrophones transmit on. If buying multipe systems you should buy different frequencies.

Q: 7. Can OBS pick this up as two seperate video sources?

A: Yes it can.

Q: 8. Without the 5 degree spot meter attachment, that costs over $100, what is the angle of measure for reflected light? Is it 40 degrees like the Sekonic L308?

A: The KFM-1100 meter unit is an incident-light reading meter.To use for reflected readings, one of/or two additional attachments need to be purchased: KFM-400 attachment which gives a 40degree angle, or a spotfinder attachment which gives 5 degrees (refer to page 10 of instruction manual)

Q: 9. If the beacons and robot are permanently installed in a room and have been centered once do you have to center them every time you power off and back on?

A: Once your beacons and robot are setup for one location, you will not have to center the units again. You will only need to center the units once the robot and beacons are moved to a different location.

Q: 10. This says 60Hz, is there a model that will work in Pal 50Hz countries?

A: B&H offers only the North American version. We do not offer a different version for use overseas.