The precise and fluid Arca-Swiss Core 75 Leveler cp MonoballFix Leverfrom Arca-Swiss Core 75 Leveler cp MonoballFix Leveris equipped with a dovetail clamp that is compatible with monoballFix plates and Arca-Swiss monorail cameras. The clamp easily locks down by pressing the monoballFix mechanism. The head works on arc movements that keep your camera centered over your tripod, so you never lose your center of axis. Each X and Y axis has +/-15° of micrometric adjustment, which is controlled by two geared telescopic knobs, which pull out if you are using a larger camera and can't reach the knobs. The head has 360° panning on both the top and bottom base, and the top pan has a scale for a repeated setup or for measuring intervals when creating a panoramic shot. The Core 75 can hold camera equipment weighing up to 66 lb, and with each movement you make, there is no need to lock a knob because of its self-locking gear.

The top of this head has a ClicPan panning platform that can be freely panned or provides panning in pre-set selectable steps. It has a range of 360° and a precision scale for precise and repeatable results.

Load Capacity: 66 lb    Adjustment Range: +/-15° on X/Y Axis    360° Panning on Top and Bottom Base    Arc Movement Keeps Camera Axis Cantered    Geared Micrometric Movements    Self-Locking Movements    monoballFix Mechanism    Telescopic Control Knobs    Arca-Swiss & monoballFix Compatible    Fits Monorails of Arca-Swiss Cameras

The leveling head can hold camera equipment weighing up to 66 lb.

The Core 75 is equipped with a dovetail clamp that is compatible with monoballFix plates and Arca-Swiss monorail cameras.

The clamp locks via its monoballFix mechanism.

The head works on arc movements that keep your camera centered over your tripod, so you never lose your center of axis.

Each X and Y axis has +/-15° of micrometric adjustment, which is controlled by two geared knobs that are self-locking.

The geared knobs telescope out, so you can reach the knob when using larger cameras.

There is a 360° pan on the top and the bottom base of the head. The top pan has a scale for a repeated setup or for measuring turning intervals when creating a panoramic shot.

Related Questions and Answers

Q: 1. Will this quickset plate fit the Arca Swiss Z1 ball head 801103?

A: Yes. But please keep in mind that the following adapts to smaller QR plates such as the following plates mentioned. 802255, 802260, 802262 and 802265.

Q: 2. Can someone clarify the two different answers below - can the dovetails be rotated on each baseplate, to switch whether the Classic or the monoballFix dovetail is the one in line with the lens axis? When I look at the additional baseplate that can be purchased separately, it seems to have the dovetails mounted in the other direction, suggesting they can be changed...

A: Hello Jonathan, Yes I confirm the dovetails can be rotated on each base plate to switch whether the Classic or monoballFix. When the plate is mounted with the narrow width parallel to the optical axis, then you can mount it on monoballFix® quik-release. When the plate is mounted with the larger width parallel to the optical axis then you can mount it on an Classic quick-release. This system is called "Dual Base". Now this L-Bracket has not been designed to change or replace the rotable plates with others monoballFix® plate. However if you absolutely need to do it, that is possible (everything is possible at ARCA SWISS :-)) but I would like to alert you on 2 points which are obvious for us but may not be clear for all the people. 1- If you replace the rotable plates/dovetail by monoballFix® plate, the you will have to choose only the ones with the grooves on their top so they will perfectely fit with the L-Bracket bases (horizontal and vertical). The compatible references are 802284, 802283, 802280, 802281, 802282 that you can find on B&H website. 2- Then you will not be able to use the screws neither the one of your L-Bracket dovetail plate (it may be too long depending on your camera base mouth depth) nor the one delivered with the additional plate (it may be too short). In that case we can provide a custom solution with specific screws but it that case we need to make a prior analysis and eventually a special order with B&H. Hope it answer your question and if you need more support, please just ask. Jean-Pierre from ARCA-SWISS

Q: 3. Does this fit the Hasselblad X2D?

A: Yes, the Arca-Swiss L-Bracket MonoballFix Universal is compatible with the Hasselblad X2D.

Q: 4. Are the plates on this L-bracket compatible with Arca-Swiss Slidefix ? I am using an Arca-Swiss item 801213 (Monoball P0 Panning with slidefix QS)

A: Yes the arca-swiss plates would be compatible across all arca-swiss brackets or panning systems.

Q: 5. Hi,I already own an Arca swiss Monoball p0 and I have adapted a different quick release system to it. I'm thinking about switching back to the arca swiss plate system. I bought some L-brackets from Sunwayfoto to fit my Sony A7R3 cameras (which are compatible with Arca-Swiss stardard). Is the MonoballFix on the Monoball p0, able to mounts these L-bracket? Or is it a smaller mount on the MonoballFix ?Also, can the tension be ajusted other than the release-lever?Lastly, are the stop-pins fixed or able to be actuated by spring pressure?

A: Its a smaller/narrower mount and incomprehensible with the standard Arca-Swiss system

Q: 6. Will this work on a Nikon D800?

A: Yes this will work for the D800. Just remove the 3/8ths thread.

Q: 7. What's the minimum distance between bolt centers possible with this plate?

A: The minimum distance between bolt centers is about 8mm.

Q: 8. Would this device hold my camera just as securely as the Fliplock or Classic with the screw devices?

A: This device can hold your camera just as securely as the Fliplock or Classic version of the clamp as long as you are using the SlideFix type plates for it.

Q: 9. Are the safety pin removable?

A: The pins are not removable by any normal means.

Q: 10. Will it fit Peak Design PROplate?https://a href= http://www.bhphotovideo.com/c/product/1096749-REG/peak_design_pl_pp_1_proplate_a_for_manfrotto.html target= _blank www.bhphotovideo.com/c/product/1096749-REG/peak_design_pl_pp_1_proplate_a_for_manfrotto.html/a

A: Yes the Peak Design PROplate is Arca-swiss compatible with this clamp, as well as Manfrotto RC2 compatible.