Whether you are an owner-operator who needs a case for your ARRI ALEXA 35 Camera or a rental house looking to protect its investment, this black ARRI ALEXA 35 Lightweight Foama Studio Case Yellow Insertwith a yellow insert from ARRI ALEXA 35 Lightweight Foama Studio Case Yellow Inserthas you covered. Nestled inside a Nanuk 960 case, the durable EVA foam is custom-cut to accommodate your camera and specific accessories.

The foam insert is custom-made to fit each piece of equipment perfectly, so you can rest assured knowing it's safe from any damage. While most foam inserts on the market are made from open-cell PE or PU foams that are less protective and not as durable, the Foama insert is designed using the highest quality closed-cell EVA foam, which is much stronger and more long-lasting than any other type on the market.

Open Box Products Have a Limited Lifetime Warranty    For Camera & Select Accessories    22 x 17 x 12.9" Interior    IP67-Rated, Dust & Waterproof    Removable Lid for Full Interior Access    Extendable Handle & Low-Profile Wheels    Lightweight NK-7 Polypropylene Resin    PowerClaw Latching System    Automatic Pressure-Release Valve    Molded-In Bezel System & Padlock Holes    Comfortable Soft-Grip Handle

• ARRI ALEXA 35 lightweight cage
• ARRI Bridge Plate Adapter BPA-6
• Two 18" rods
• Two accessory pockets
• Memory cards
• Card reader

Made of high-strength NK-7 polypropylene copolymer resin, the case is vibration and impact resistant. It has low-profile wheels and a two-stage telescoping handle so you can pull the case behind you. If you need more freedom of movement, there are three comfortable soft-grip handles on three sides for hand-carrying. Additional design features include gasket sealing that brings the case to an IP67-rating to be dust and waterproof, a molded-in hinge for added strength, stainless 0.34" diameter steel reinforced padlock holes, and four PowerClaw trigger release latches that compress the O-ring and seal the case tight. A built-in automatic pressure release valve equalizes the pressure in the case when traveling by air.

Related Questions and Answers

Q: 1. How do you adjust the temperature with knob?

A: That is not a knob, it's for the pressure regulator inside the case.

Q: 2. Shooting on a boat, let's say I need to swim from an anchored sailboat to shore, not terribly far, would you feel confident floating the case in the saltwater for the swim?

A: I think it is likely that the Pelican folks would agree that this is risky. I have never tried it; maybe it would be ok. However, fully loaded, your case+contents can be very heavy is unlikely to float. Stripped of the bags and with a light load it would float but chuck full ... i doubt it. The seals are pretty robust though. So, if you have maintained the o-rings, etc, it is likely to be dry inside after exposure to water. If you are just transporting a light load, it may float and there is a reasonable chance that this box will protect your equipment. If you are carting several thousand dollars worth of equipment, though, I would not risk attempting to float the package.However, I cannot think of a better container to protect your equipment from damage were the trip to the water to be accidental.You could, of course, put some weights in the box and see how it works. Be sure to expose it to some waves.

Q: 3. What is the diameter of the largest tube?

A: The diameter of the largest riser on the ARRI AS-1 Lightweight Light Stand BH #ARLSAS1 is 1 and 1/8".

Q: 4. where can I buy this padded lid organizer separately? The only ones I see listed on the Pelican website are see through mesh.

A: I see them on ebay for $82

Q: 5. Can you confirm the closed length of this stand in inches? The listed specs of 2.25 feet or .106 meters are different lengths.

A: This stand has a closed length of 27 inches.

Q: 6. 1510sc or 1560sc which 1 will fit a 16inch MacBook Pro?

A: The 1560SC Protector Studio Case will fit 15"-17" laptop computers

Q: 7. Is this stand compatible with arri 650w lights?

A: This stand has an industry standard 5/8 stud, that should work with your Arri 650w lighting.

Q: 8. Is this case large enough to hold two camera bodies (canon 5d mark ii & 7d mark ii) + four lenses (largest is 100-400mm f/4.5-5.6L) + spare batteries, cleaning supplies, etc.? I'm not sure if this case or the 1560 is the way to go.

A: Do this: lay out your kit on a table and arrange within each case's specified dimensions. Within the 15010, plan for padded inserts spanning 1/2 -3/4 separation between each item. If you want more separation, the pick and pluck foam and the 1560 may be a better option.

Q: 9. Can this fit 2 lightstands and umbrellas in addition to cameras and lenses?

A: Doubtful. I use it for a 15 laptop and accoutrements along with a few drives, Cables a set of walkies and a few odds n sods for my DIT kit.

Q: 10. does this work with Arri MAP2/1?

A: The ARRI Lightweight Camera Handle LCH-1 is compatible with the Alexa 35 and the ARRI MAP-2 Adapter Plate is compatible with the ALEXA Mini. The handle and adapter plate do not interact with each other.