Telesin Long Thumb Screw 2-Pack For Camera Mounting

Telesin Long Thumb Screw 2-pack For Camera Mounting

Product Code: eq128685
Availability: In Stock

$9.87 $15.10

Qty

17 reviews Write a review

Description
Reviews (17)

Secure the housing or frame of your action camera in place with these Long Thumb Screws (pair) from TELESIN. They work with any three-prong mounting accessory.

For Action Camera Housings & Frames

General
Compatibility	Select Action Camera Housings/Frames
Physical
Mounting	1x 1/4"-20 Screw
Color	Black
Dimensions	Not Specified by Manufacturer
Weight	Not Specified by Manufacturer
Packaging Info
Package Weight	0.035 lb
Box Dimensions (LxWxH)	6.8 x 6.05 x 0.65"

Related Questions and Answers

Q: 1. What type connection cable does it come with and where does it connect?

A: It comes with a LEMO cable and connects to the port above the pan motor of the R2.

Q: 2. Does it fit on leica M240 ???i wanna buy it but i got M240

A: It fits but it doesn't sit flush in the hot shoe, nor does it come all the way to the thumb dial.

Q: 3. What is the thickness of the plastic knob? I assume that the 11mm spec is the length of the metal screw. I need a spacer to raise a camera a few mm above the tripod mounting plate.

A: 11 mm does refer to screw only. Knob is additional 7-8 mm thick

Q: 4. When you slide the Thumbs Support does it scratch the camera? or does it has rubber between the camera and the thumbs support?

A: YUP/its nicely protected and very helpful

Q: 5. Can these be used with the Pyro S TX and RX?

A: Hollyland does not recommend using the Hollyland 2.4 & 5 GHz Thumb Antenna for Pyro 7 (2-Pack) with the Pyro S. They recommend using the following antenna for the Pyro S. Hollyland Paddle Antenna for Pyro Series (2.4/5 GHz) BH #HOHLATN14

Q: 6. Where does this mount?

A: Most people mount it to the right or left sides of the R2's ring mount.

Q: 7. How long is the connection cable?

A: The cable is approximately 9"/ 228mm.

Q: 8. Can I get a cable extension for use on a Steadicam? What LEMO connector is it?

A: Unfortunately there is not dedicated extension cable for the DJI Ronin 2 Thumb Controller. DJI suggests using a USB-A extension cable to extend the included control cable's reach. A USB-A male to female cable that supports data transmission will suffice, such as the Pearstone USB 3.0 Type A Male to Type A Female Extension Cable - 6' (BH #PEUSB3AA6).

Q: 9. Will this screw fit the sliding plate for a Libec H70 head? I need to attach a Panasonic P2 HD AG-HPX170P to it. The Panasonic manual says the P2 requires a 1/4-20 UNC screw. The mounting hole is 5.5 mm deep.

A: For the Libec H70 Fluid Head we recommend the Miller 1/4"-20 Screw for Miller Quick Release Plates BH #MI036 • MFR #036.

Q: 10. Will this thumb support work when the CL is in the Protector case?

A: Yes it will.

Monika	23/09/2024
[Black] It does what it should, however the image makes it a little bit bigger than you anticipate. 5

Jason	23/08/2024
[0.035 lb] Always playing around with new ways to mount little LEDs and the bottom threads are key for versatility. 5

Joe	15/08/2024
[0.035 lb] Bought these to replace a lost screw for my camera bracket. No complaints, works as it should. 5

Arvids	11/08/2024
[Black] Fine for what it is. 5

John	09/08/2024
[0.035 lb] I use a side hand strap. To use a tripod had to remove screw on the bottom and strap and screw in to the tripod The camera screw above allows me to use the tripod with out removing the strap from the camera. This is a great time saver and makes shooting with a tripod easier. I have found no cons to the product works exceptionally well. 5

Debra	08/08/2024
[Black] Haven't used yet but seem fine. 5

Bo	18/07/2024
[Black] just thing I need 5

Dave Vlogger	05/07/2024
[0.035 lb] I bought this to use with the Vello CB-600 Flash Bracket, and it fits the bracket just fine, but I had to return it because it was the wrong size for me. One word of caution: Vello sells this product in 2 lengths: 14mm and 11mm. I have a Sony a5100 and Zoom H1, which both have pretty standard 1/4 mount holes, and this 14mm screw is too long for mounting those to the Vello CB-600 bracket. It goes through the bracket fine, and screws into my gear, but it's so long it does not tighten down all the way on the bracket, so my gear was jiggly and not dialed down all the way. I didn't actually buy and try the 11mm, but I'm pretty sure that will work better. If you have different gear with longer screw holes or stack something else in between the bracket and your gear, maybe this 14mm length is what you need, but it was too long for me. 5

hercster	27/06/2024
[0.035 lb] This is a simple product that does what its supposed to do. I purchased spares as losing them can be a critical mistake. 5