Created exclusively by Vicoustic Flat Panel VMT Acoustic Tile Pumpkin Orange 4-Packin the is made from VicPET Wool - a material produced mainly from recycled plastic bottles. With an innovative dyeing technology, Flat Panel VMT panels can simulate concrete, marble, wood and other materials, achieving an amazing and realistic look in any setting.

Flat Panel VMT panels are designed to perform primarily in the medium and high frequencies. Therefore, these panels provide a great acoustic solution to implement in any commercial or residential setting and can be used on ceilings and walls. The applications for Flat Panel VMT are infinite, making it perfect for both new construction and refurbishment projects.

Residential and Commercial Applications    Medium and High Frequency Absorption    Fire Rated    Easy to Apply

Related Questions and Answers

Q: 1. Any chance you can squeeze two monitors in this?

A: This has interior dimensions of 8 x 5 x 1.5". It is just a matter of if the 2 monitors would fit within those parameters.

Q: 2. How much foam margin is there along the interior sides with the Pick-and-Pluck foam? I want to be able to put a Mackie 802VLZ4 mixer in here, at 10.7 x 8.9 x 1.8. It should fit, according to the dimensions given here, but the Pelican custom foam builder says it won't.

A: The foam has a snug fit but I very compressible. I've found that you can squish the 1/2 cube down to 1/8 . That's if you don't care to take your cargo in and out often. I give my gear two or three cubes for easy in and out. The overall gap between the foam and the side is about 1/16 or so. Hope that helps.

Q: 3. How does the twist-lock mechanism hold up over time? I photograph at the beach a lot and am worried about sand.I'm not very familiar with ball-heads - will they support my Bronica SQ ok? (It's under 8 pounds).

A: For my experience, I have a Fujifilm X-E1 with a telephoto lense and flash attachment. Altogether I don't think there are more than 8 pounds of load, but I like the twist-lock mechanism and its convenience. It's been holding up quite well for my hiking and mountain bike trips. I have gotten it wet with sand a few times and I usually wipe everything down after removing the parts. The thing you'll have to be careful is water, they tend to sip inside the legs where you twist to loosen it for extension, as that motion might bring water further in. I do say removing everything and putting it back together will do, but it's a 10-15 minutes task - but hey, it's all for keeping the equipment in good shape!

Q: 4. Hi,will a Fuji XT5 with the 27mm 2.8 fit?

A: Yes, the WANDRD D1 Fanny Pack will fit the FUJIFILM X-T5 Mirrorless Camera with the FUJIFILM XF 27mm f/2.8 R WR Lens attached.

Q: 5. Can this case hold both Fujinon MK18-55mm and mk50-135mm t2.9?

A: Same as original,Yes.

Q: 6. Is this the model with the pick n pluck foam?

A: Yes it is the pick & pluck foam. This case works great for me.

Q: 7. can I bring this as carry on?

A: Yes. Just make sure you have it locked with the travel padlocks. Security will want to open it to check the contents.

Q: 8. Will this fit the SmallHD 701?

A: I believe it will. I'm able to store my tv logic 5.6 in the main compartment with the AC power supply right next to it.

Q: 9. Will the ATN X-SIGHT II HD 5-20x fit in the 1200 or the 1170?

A: The 1170 would work

Q: 10. Will this work with a Canon 5D Mark III ?

A: It will work with a 5D, but if you want to be able to use larger lenses and have a proper ballhead for vertical mode I would recommend the RoadTrip or GlobeTrotter model.