Wrangle your controller's velocity output with the MIDI Solutions Velocity Converter, an inline MIDI utility device that applies selected velocity curves to incoming MIDI notes. Curves can be selected from 40 presets, which offer solutions for most velocity processing requirements, while a user defined curve allows you to create a curve to your exact specification.

Applies Velocity Curves to Incoming Note    40 Velocity Curve Presets    User Defined Curve    Set Separate Curves per MIDI Channel    SysEx Programming via Free Software    5-Pin DIN MIDI Connectors (In x Out)    MIDI Powered

• Apply a separate curve to each MIDI channel, allowing the velocity response of a sending keyboard to be matched to individual sound modules that are set to receive on different MIDI channels.
• Assign velocities based on a selected incoming Control Change value. In this mode, the Velocity Converter stores the value of a selected Control Change message on a selected MIDI channel and applies this value to all incoming velocities on that MIDI channel. It is also possible to add an offset to this value to keep the outgoing velocities above a specified level.
• Program by sending it MIDI System Exclusive messages. This is easily done with the MIDI Solutions Programming Tools software. Once programmed, its settings are retained even after power is removed. The Velocity Converter can be reprogrammed with new settings as often as needed.
• The Velocity Converter is MIDI-powered and requires no batteries or power supply to operate with most MIDI products. A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

Related Questions and Answers

Q: 1. Does the motu m2 can work fine with a pair of Yamaha HS7 studio monitors?

A: Yes, they will work well together. You will just need a pair of 1/4" TRS to TRS cable to connect them: https://www.bhphotovideo.com/c/product/1036641-REG/pearstone_pm_trs03_pm_series_trs_m_to.html

Q: 2. Can we output audio from both Input 1 and Input 2 simultaneously to the usb so that we hear both inputs at the same time (mono-mix or stereo mix)?

A: Yes. This will allow two simultaneous inputs.

Q: 3. Can I power this with a USB-C powering jack (wall wart) and use it without a computer?

A: Yes, it can be powered via a USB-C wall adapter and used as a standalone pre-amp.

Q: 4. I can't get the m4 to turn itself off when the computer shuts down. Has anyone got this to work? Every other usb device does this.

A: The MOTU M4 has a physical on/ff switch, so if your computer is sleeping it will remain on. In order to have it shut down with your computer, you may have to adjust settings in your computer to stop power being sent to USB when shut down.

Q: 5. It appears that the Monitor 1/2 and Line 1/2 both only output Channels 1 and 2. Is that correct? Can Channels 3/4 be outputted

A: Both the Monitor 1 and 2, and Line Out 3 and 4 connectors on the MOTU M6 USB-C Audio/MIDI Interface can be used for connecting monitor speakers or sending line level output to another destination, carrying the output signal from all four input channels. Additionally, the Monitor 1 and 2 outputs are labeled as "A" to use for primary monitor speakers, while the Line Out 3 and 4 connectors are labeled as "B" to use for a secondary pair of monitor speakers.

Q: 6. Can you actually record true 32 Bit Float through this interface?

A: No, the M4 does not offer 32-bit floating point recording.

Q: 7. Do the 1/4" TRS outputs and the RCA outputs operate simultaneously?

A: Yes, the 1/4" TRS and RCA outputs on the MOTU M2 USB-C Audio/MIDI Interface can be used simultaneously to connect two sets of speakers or to route the signal to the line level input on another device.

Q: 8. Can you connect it directly to the new IPad Air 4th gen, via USB-C, or do you need an adaptor/CCK?

A: Yes, the MOTU M4 can be connected directly to iOS devices with USB-C running iOS 9 or later using a standard USB-C to USB-C cable.

Q: 9. I see the "mon" button for monitoring the live input signal. Is there a way to control the mix of live input and computer audio send to the headphones?

A: On the M2, there is no specific way to control the mix of direct monitor and computer audio. On the M4, there is an Input Monitor Mix knob which will allow you to control the blend.

Q: 10. Is the MIDI end of this cable male or female?

A: The MIDI connections on this adapter cable are female.