Providing control and video outputs for the Toshiba IK-HD1H camera, the Toshiba IK-HD2C Camera Control Unit with HD-SDIis a small interface box compatible with NTSC frame rates. As most camera controls are accessible from the front of the unit, the CCU is easy to operate via the front panel, or you can use an optional RS-232c remote control connected to the back of the unit. Front panel controls include; power On/Off, AWB and gain switch, buttons for menu selection and a button to change scene files and display modes.

The rear of the unit provides 59.94i to 60i format selection, as well as a key lock On and Off switch. Also located on the back of the unit are the Ext. Sync in and Sync out ports, a wired remote control terminal and a 12 VDC power input. This CCU only works with the IJ-HD1H remote camera head, which is not included, and requires a compatible camera connecting cable and 12 VDC power supply, both of which must be sourced separately.

For IK-HD1H Remote Camera Head    Supports 1920 x 1080i Video    5 User Assignable Scene Files    HD-SDI, Component/RGB Outputs    Switchable 59.94/60Hz

On Screen Display, when connected to an optional monitor.

Auto Black Balance.

White Balance: ATW (Auto Tracking), AWB (Automatic), Manual.

Five user programmable user files are available for camera settings.

The CCU provides image processing control of:

• Gamma correction leve -10 to 10
• Detail gain -7 to 7
• Master Pedestal -200 to 200
• Red pedestal -100 to 100
• Blue pedestal -100 to 100
• digital Noise Reduction on/off

You can also use Matrix color correction primary and secondary color hues

Electronic Shutter with auto, manual, and Synchro Scan. Synchro scan allows you to adjust the scan rate to remove roll bar when shooting a monitor.

Automatic / Manual lens shading correction.

Related Questions and Answers

Q: 1. need 10 pin remote cable to 10 pin remote cable ?

A: This product comes standard with a 10-pin, 10 meter (32 foot) remote control cable.

Q: 2. Will this work with the Nissin i60?

A: The SF C1 will pair and trigger the generic Nissin i60 by itself. However once attached to any Leica camera pressing the camera shutter the generic Nissin i60 will NOT fire. It will only work with the Leica branded SF60 flash only. It would seem there is a proprietary lock in SFC1. Now if you were to take the canikon or sony version of this commander (air 10S) it would sync and fire across all versions of the i60 flashes except Leica.

Q: 3. Does the Leica SF C1 remote control unit work with the Leica D-LUX7 Camera?

A: No, the Leica SF C1 Remote Control Unit does not work with the Leica D-LUX7 camera.

Q: 4. Will this work with the Leica S (typ 007)?

A: Yes it is compatible.

Q: 5. Can I use two iPads to control two diff. scenes from one Apollo Bridge?

A: No, the Litepanels Apollo Bridge Wireless Control Unit can work with one ipad at a time. It can not work with two at the same time.

Q: 6. Does Leica SF C1 work with Nissin MG 10?

A: Yes, they work together.

Q: 7. can this be used as a ccu through a telecast copperhead system?

A: I have been unable to find out from Panasonic or the cable manufacturer if this combination will work as you wish. I will have to recommend that you contact a video engineer with expertise in this equipment.

Q: 8. Is this microphone can connect to android device?

A: No it cannot be used with Android devices: For iOS, Mac, and Windows Platforms

Q: 9. Is Apollo Bridge RDM ready ?

A: Yes. The unit is fully RDM ready

Q: 10. Does this work with Nikon SB-5000?

A: They are not compatible.