The MX-40PI Wired Indoor Passive Infrared & Microwave Combination Detector with Immunity from Optex combines the microwave and PIR technologies in attractive, easy-to-install units, and provides unprecedented reliability and detection performance.

The detector incorporates Anti-Crosstalk technology which prevents false alarms caused by microwave interference when several detectors are operating in the same area. It features Quad Zone Logic, which discriminates between human beings and other sources of infrared. This detector also features switchable on/off LED alarm indicator.

Patented Quad Zone Logic    Spherical Lens Design    Anti-Crosstalk Technology    Noise Reduction Circuit

Optex utilizes microwave technology in designing the antenna settings for this detector. The result is a non-conventional Anti-Crosstalk System which prevents interference from other microwaves. Reducing interference enables the detector to prevent false alarms typically caused by numerous matching frequencies in one single area. Complete with a noise reduction circuit, the detector is able to cancel noise that enters the antennas, thus eliminating microwave interference. The high-quality, highly reliable detector is the solution for false alarms caused by outside microwave interference.

The MX-40Pl Detector creates an integrated detection area. This enables the microwave detection area to synchronize to the PIR detection area, achieving higher detection performance and preventing errors and false alarms.

With uniform distance between each lens segment and the pyroelectric elements, the spherical lens provides a precise focal length to each of the multiple lens segments. This enables each lens segment to precisely face its detection area and creates detection zones without distortion, achieving a new level in lens design precision. The lens has a spherical design that makes it highly resistant to damage and outside disturbances.

The Noise Reduction Circuit provides reliable performance against outside noise such as electromagnetic interference and noise caused from fluorescent lights. As a result, the possibility of false alarm is greatly reduced.

The highly accurate and reliable detection pattern will maintain its sensitivity through the entire detection area, even in high temperature or low contrast environments. Quad Zone Logic creates an extremely high vertical zone density. These taller zones capture the entire body mass and enable detection of even the smallest temperature contrast against the background. In addition, the vertical detection density has been improved to take into account dead zones created by furniture or partitions.

The MX-40Pl detector allows for a simple 2-step adjustment. Setting the range selector to short or long range detection according to the room size makes adjustment during installation much easier and less time consuming.

The PC board is removable for simple wiring. With the simple use of a screwdriver, a firm tap will easily remove the knockout.

The compact and stylish body matches any interior design without disturbing the decor.

Easy installation and wiring are engineered into this compact housing. The long or short distance selector switch makes microwave area adjustment easy.

Related Questions and Answers

Q: 1. Will it cross room thresholds and how is it on carpet?

A: The enabot Ebo Air Familybot BH #ENEBOA will traveerse thresholds that are smooth and not too high and all but the shaggiest of shag carpeting.

Q: 2. Hi guys, My pad says that I have a fault number 2 which means battery of the sensor is low. I removed it to change the battery, however I can not locate the battery. Is there even one? Any idea to help? Cheers

A: This is a hard wired motion sensor, there is no battery. My suggestion is to contact the Alarm installer. Low battery can be the backup battery on your panel. or an RF alarm sensor.

Q: 3. Does the transmitter come with a receiver or do I need to order the receiver separately?

A: This is the transmitter only. You can search on our website for "Optex wireless 2000" and the kit will come up.

Q: 4. Will the Optex TR-20U operate announcing in 2 locations?

A: It will work with up to 4 transmitters.

Q: 5. Will it find it's way back to the charging station from secondary rooms?

A: The enabot Ebo Air Familybot BH #ENEBOA will find its way back to its charging dock from secondary rooms.

Q: 6. what is the input voltage of this device and can it be wired to control 3DC Volts ?

A: The Bosch ISC-BPR2-W12 featues: Current: Alarm/Standby: 10 mA at 12 VDC Operating Voltage: 9-15 VDC

Q: 7. Can the door station be mounted over an existing peephole if battery powered?

A: From what I saw in the installation video, it looks like it needs to be mounted on a wall like you would a doorbell or other WIFI video doorbells.

Q: 8. Can the tablet work work while on the charger?

A: Yes, the screen is meant to be connected to a power supply in order for it to power up and work.

Q: 9. is the td-20u compatible with my old wireless 2000?

A: Yes

Q: 10. how do you replace the battery in a BX 80?

A: Instructions for changing out the battery can be found in the product manual at the following link: http://bit.ly/1OufWkr