Add HDMI output to your Q16pro video processing chassis with this RGBlink Dual HDMI 2.0 Output Module Q16profrom RGBlink. This hot-swappable module features two HDMI 2.0 outputs that support video signals with up to 4K60 resolution. It supports a maximum source input video height of 4096 pixels for output via this module.

Output Card for Q16pro I/O Chassis    2 x HDMI 2.0 Outputs    Supports Video up to 4K60    Hot-Swap Capable    Maximum Video Height: 4096 Pixels

Related Questions and Answers

Q: 1. Can this T-Tap cross convert so the different outputs are send out different formats?

A: no it can not.

Q: 2. will this splitter work to connect a wacom one pad and a monitor?

A: No it will not.

Q: 3. Can this output different formats between the two outputs?

A: No it can not. The SDI and the HDMI outputs must be the same resolution.

Q: 4. does this work with fcpx?

A: AJA does show FCP X on their website for compatibility.

Q: 5. Are the output ports mirrored or can I send different output content to them independently?

A: Both outputs can be used simultaneously at all times, and the HDMI output can be connected directly into 4K HDMI monitors for monitoring HDR video in PQ, HLG, HDR10, and Dolby Vision formats with third-party support.

Q: 6. Does this actually record 4K30 signal? The specs here say "Capture up to UHD 4K30 to Your Computer" and ..." lets you capture up to UHD 4K signals with embedded audio via an HDMI input" But after sifting through the specs on the manufacturer website found this little nugget. "Record in up to 38402160 resolution (4k) at 30Hz with hardware up-scaling/down-scaling. The dongle will accept 4K/30Hz signals from a gaming console and will automatically downscale the output video to 1080p/30 HD HDMI video signals if needed." Huh? So, is this 4K or 1080 with upscaling. So, it accepts 4K, then converts it to 1080P, then UPSCALES back to 4K for recording? This seems like a terrible way to record 4K. Unless I'm not understanding something? Please clear this up.

A: The KanexPro 4K HDMI to USB 2.0 Capture Box with HDMI Loop Output can accept HDMI sources up to 3840 x 2160 30p and output up to 3840 x 2160 30p on the HDMI output and downscales to 1920 x 1080 30p for the webcam signal over USB 2.

Q: 7. Will this splitter work with Atem mini extreme hdmi out put 1 to split to 4 television displays

A: Yes, while we have not tested the Kopul HDMI 2.0 1 x 2 Splitter with the Atem Mini, it should work if you wanted to split the HDMI output. Please make sure to choose the 4 output mode listed below: Kopul HDMI 2.0 1 x 4 Splitter BH #KOHDMISP1420 https://bhpho.to/3ZkX172

Q: 8. Does this work with Davinci Resolve Studio?

A: Unfortunately, the AJA T-TAP Pro Thunderbolt 3-Powered Converter with 12G-SDI and HDMI 2.0 Output is not compatible with Blackmagic Design Davinci Resolve. Blackmagic Design is particular with its expansion devices and will need its own models.

Q: 9. Looking to split the output from a 4k security camera system to 4 TVs thoughtout the house (3' to 75' away). Will this work?

A: Yes it will however you may want to use an extender for your longer cable runs. HDMI cables require boosters or extenders if you intend to run cables longer than 35 feet.

Q: 10. Captures audio too?

A: Yes, The KanexPro 4K HDMI to USB 2.0 Capture Box with HDMI Loop Output supports Audio. It supports - USB Audio UAC standard.