Power several rows of modules with the 4ms Row Power 45, a 4 HP Eurorack modular synthesizer power supply that powers up to 3 typical rows of modules in an enclosure or skiff. Two barrel jacks allow you to daisy chain to multiple Row Power modules (or Pod enclosure) using a single common laptop-style power brick (sold separately), which can power 3 to 5 rows of modules. A power switch cuts power without interrupting the daisy chain.

The Row Power 45 is compatible with the 4ms Row Power Shield (sold separately), a device that attaches to the back of the Row Power 45 and monitors the amount of current being drawn, as well as the voltages of the power rails. The information is transmitted wirelessly via Bluetooth and displayed on a phone or tablet. The Row Power 45 ships with a set of mounting screws.

Clean, Regulated, and Protected Power    Provides 45W of Power    Power 3 Typical Rows of Modules    Requires Barrel-Style Power Brick    Works with Flying Bus Cable + Bus Boards    Direct Connection Compatible    Two Barrel Plugs for Daisy Chaining    Compatible with Pod Enclosures    Includes Mounting Screws

• Two power jacks for daisy-chaining multiple Row Power units: a common laptop-style power brick could typically run 3-5 rows or Pods
• On/off switch cuts power without interrupting the daisy-chain
• Row Power 45 provides more than enough power for three typical rows of modules
• Ultraclean: Each rail is separately regulated with high-grade components
• Row Power 45 is efficient, so it won't heat up your system
• Skiff-friendly: only 1.01" (27mm) with power connectors installed
• CV/Gate headers for expansion
• Solder holes for DIY/custom power distribution boards: fits MTA156 headers or 14 AWG wire
• Compatible with 4ms Power Watcher BT, which connects to header on back of RP45

• 15 to 20 VDC power brick or barrel jumper cable to daisy-chain from a powered Pod or Row Power
• Flying-bus cables, Bus Stick, or other distribution system (for connecting Row Power 45 to multiple modules)

Related Questions and Answers

Q: 1. Is it possible to mount this via 1/4-20" instead of the cold shoe?

A: Yes, beneath the cold shoe of the edelkrone Power Module (V-Mount) reveals a 1/4"-20 receiving point.

Q: 2. Will this bag hold a Z9 with 500PF attached with room for a Z100-400 also?

A: No the bag does not have the interior height to hold a gripped camera body like the Nikon Z9 Mirrorless Camera.

Q: 3. Could this keep my gear warm while skiing?

A: Yes it does and it will do the job you want it to for skiing. However, there are other backpacks that would be better suited for you in regards to skiing. I have noticed with this bag that its a bit bulky so getting on and off chairlifts can be anoying because you have to take off and put on the back pack everytime ou get to a lift. Also, it can be a bit difficult to ski with at times, I noticed this more if I didn't have the strap size right, but it doesn't have a waist strap so it has a tendency to bounce a little more. Also every time you want to get your camera out of the bag you have to take it off and lay it in the snow which can be annoying.Overall this is a good backpack and it will do the job you want it to. However, there are other back packs that would be better suited for you, especially if you wanted one specifically for skiing. Id recommend a sling bag or one that has a wait and chest strap, and can be easily accessible and wont get in your way skiing.

Q: 4. Will this unit communicate battery telemetry to the Komodo?

A: The Tilta V-Mount Advanced Power Distribution Module will allow you to see your remaining battery life as a percentage on the RED Komodo’s user interface. It will also display 100% battery life for any voltage over 16V and will hit 0% at 12V which will align perfectly for most batteries.

Q: 5. Is it possible to provide power to the module via the Anton Bauer P-Tap Charger that's plugged into the wall?

A: Yes, you could use a Gold mount power supply with the edelkrone Power Module (Gold Mount). However, using batteries would be more cost effective. Gold Mount wall power supply idea: Anton/Bauer Tandem-70 On-Camera AC Power/Charger BH #ANT70

Q: 6. I'm a big guy how far will the chest and waist strap go?

A: According to the manufacturer, the straps on each side of this backpack measure 16 long at full extension.

Q: 7. Is it possible to power a camera from this module? Is there a known good cable to go from the power module to a Sony NP-FZ100?

A: The edelkrone Power Module (V-Mount) is designed to only power edelkrone products. However, you should be able to work with this cable: Kondor Blue D-Tap to NP-FZ100 Dummy Battery Cable B&H # KODTSA7SDBBK or DigitalFoto Solution Limited Sony NP-FZ100 Fully Decoded Dummy Coiled Cable BH #DIDC12

Q: 8. Will the rec/stop from Tilta Nucleus work without delay?

A: Typically there is no delay when working with the Tilta Nucleus solutions.

Q: 9. Till this device be RED approved and therefore send battery voltage information to the camera?

A: Yes, When using Gold Mount batteries, this module will fully communicate with your camera body, allowing you to see your remaining battery life as a percentage on the RED Komodo’s user interface.

Q: 10. Is the main compartment 2 zippers where you can access just the top part to get to your camera or one zipper that you have to unzip the whole panel to get to it at the top?

A: The lid has 2 zippers for its' 2 small compartments.The lid itself is opened by two zippers, (one on each side - 1 zipper would be a pain to deal with), to access all your camera(s) and lenses at one go. It is a great bag for the price.