Ashly Nxp8004 4-Channel 800W Power Amplifier

Ashly Nxp8004 4-channel 800w Power Amplifier

Product Code: eq13971
Availability: In Stock

$10,137.00 $14,901.39

Qty

13 reviews Write a review

Description
Reviews (13)

The nXp Series NXP8004 4-Channel 800W Power Amplifier with Programmable Outputs & Protea Software Suite from Ashly is a Class-D switching amplifier combined with a switch mode power supply. This amplifier meets the requirements of demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.

This amplifier features Protea DSP processing for efficient control. The rear panel has DIP switches for programming each channel output for either High-Z or Low-Z operation. This amplifier can be connected to a network with Ethernet control and features serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability, all controlled using the included Protea Software Suite.

The amplifier offers 32-bit SHARC DSP processing (with 48 & 96 kHz sampling) for comprehensive audio processing and built-in signal generator for test tone and noise-masking. It also offers swept load impedance monitoring on each amplifier channel output.

Processor
Input Source	Protea DSP Options: Analog, auto (net, AES3, analog)
Limiter	Brick Wall Limiter: Threshold: -20 to 20 dBu Ratio: Infinite Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB
Control	Advanced Gate Controls Key Engage Enable Key Frequency: 20 Hz to 20 kHz Key Bandwidth: 0.016 to 3.995 octave
Gain	Gain (with / without VCA): -50 to 12 dB, off, polarity invert Digital VCA Groups: 4 available Remote RD8C Gain: Enable per channel, 0 dB to -∞ WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute
EQ Type	For 31-Band Filter Type: Constant Q or proportional Bandwidth: 0.499 octave to 0.25 octave For Parametric 2,4,6, or 10 Band Frequency: 20 to 20 kHz Level: -30 to 15 dB Q Value: 0.016 to 3.995 octave For Hi / Low Shelf 6 / 12 dB/octave Frequency: 20 Hz to 20 kHz Level: -15 to 15 dB For All Pass Frequency: 20 Hz to 20 kHz For Variable Q HP / LP Frequency: 20 Hz to 20 kHz Q Value: 3.047 to 0.267 For Notch / Bandpass Frequency: 20 Hz to 20 kHz Q Value: 92.436 to 0.267 Feedback Suppressor (48 kHz Sampling Rate) 12 x filters In/Out per filter Lock (per filter) and global lock Filter Modes: Float, restricted, manual Filter Type: Notch, parametric Filter Frequency Range: 20 Hz to 20 kHz Notch Filter: -∞ Parametric Filter: 15 to -30 dB Filter Bandwidth 0.016 to 3.995 Octave Detector Sensitivity: 5 levels Float Time 5 minutes to 24 hours
Filter	FIR Filter: .fir or .csv file types
Crossover	2-Way, 3-Way, 4-Way Crossover & High Pass / Low Pass Filters Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave Frequency: Off, 20 Hz to 20 kHz
Delay	Sampling Rate: At 48 kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 21 ms Delay: 0 to 682 ms At 96 kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 10.6 ms Delay: 0 to 341 ms
Audio Metering	Range: -60 to 20 dBu Increments: 1 dB Peak Hold Indicator
Signal Generator	Pink Noise, White Noise, Sine Wave Signal Level: Off, -50 to 20 dBu Sine Wave Frequency: 20 Hz to 12 kHz
Processor	Input A/D, Output D/A: 24-bit DSP Processors: 32-bit floating point Sample Rates: 48 kHz, 96 kHz Propagation Delay @ 48 kHz: 1.42 ms Propagation Delay @ 96 kHz: 0.71 ms
Mixer	Gain (0.5 dB Increments): Off, -50 to 12dB Mute: Per channel Auto-mixer Enabled: Per channel Global Auto-mixer Response: 0.01 to 2 sec Enable Ducking at Mixer Ducking LED: Per channel if enabled Metering: Level, auto-mixer level
Compressor
Threshold	-20 to 20 dBu
Ratio	1.2:1 to infinite
Attack	0.2 to 50 ms
Release	5 to 1000 ms/dB
Detectors	Peak / average
Attenuation	2 available
Metering	In, out, attenuation, graphical
Auto Leveler Controls
Level	Target Level: -40 to 20 dBu
Action Type	Gentle, normal, aggressive, user defined
Maximum Gain	0 to 22 dB
Metering	Input, gain, attenuation
Ratio	1.2:1 to 10:1
Threshold	-30 to 0 dB
Gain	5 to 1000 ms/dB
Hold	0 to 6 seconds
Ambient Noise Compensation
Output Gain	Maximum: -20 to 20 dB Minimum Base: -40 to 20 dB
Gain Adjustment Range	0.2 to 20 s/dB
Groups	Link Groups: 16 available
Input Channels	ANC: 1 to 4
Threshold Range	Output Noise: -40 to 20 dBu
Ratio	Program/Ambient Gain: 0.3:1 to 3:1
Metering	Input level, attenuation, average noise
Ducking	Trigger Threshold: -80 to 20 dBu Ducking Release: 5 to 1000 ms/dB Ducking Depth: 0 to -30 dB, -∞ Enable Ducking at Matrix Mixer Metering: Input
Gate
Threshold	-80 to 20 dBu
Range	Off, 100 to 0 dB
Attack	0.2 to 50 ms/dB
Release	5 to 1000 ms/dB
Metering	Key signal, gate LED, graphical
Power Requirements
Power	At 50 Hz Nominal (Automatic Sensing SMPS): 120 VAC Operating Range: 70 to 135 VAC Minimum Power-Up: 85 VAC At 60 Hz Nominal (Automatic Sensing SMPS): 240 VAC Operating Range: 140 to 270 VAC Minimum Power-Up: 170 VAC
Connector	Power Cable Connector: 20 A powerCON
Maximum Output Power	Per Channel, Low-Z Output, All Channels Driven 2/4/8 Ω: 800 W
Output	Low Z Output, Bridge Mode, All Channels Driven: 1600 W (4/8 Ω) 70 V, 100 V Output, All Channels Driven: 800 W (70/100 V (per channel)
Power Draw	Sleep Mode: < 1 W Standby Mode: 40 W Idle (No Signal): 70 W
Current Draw	For 120 VAC Sleep Mode: 0.1 A Standby Mode: 0.70 A Idle (No Signal): 1.30 A For 240 VAC Sleep Mode: 0.05 A Standby Mode: 0.35 A Idle (No Signal): 0.65 A Maximum, All Channels Driven, Typical Input 1/8 Max Power @ 2 Ω): 8.8 A for 120 VAC, 4.4 A for 240 VAC
Dissipation	Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 136 BTU/hr Idle (no signal): 238 BTU/hr Typical (1 / 8 Max Power @ 2 Ω): 970 BTU/hr
LED Indicators	Front Panel LED Indicators White: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On (fault condition or shut down), Off Green LED: Signal Per Channel: -18 dBu, below rated output Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% maximum operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled
General
Voltage Gain	Selectable at 26, 32, or 38 dB, and 1.4 V
Damping Factor	>250 (8 Ω load <1 kHz)
Filter	Input High Pass Filter: 80 Hz 2nd order
Distortion	<0.5% SMPTE, typical <0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz)
Channel Separation	-75 dB (dB from full output, 1 kHz)
Signal / Noise	20 Hz to 20 kHz, un-weighted: >108 dB
Frequency Response	20 Hz to 20 kHz, ±0.05 dB
Connector	Balanced Input Connector: Euroblock 3.5 mm, 1/4" TRS and XLR combo jack
Input Impedance	10 kΩ
Maximum Input Level	21 dBu
Speaker Output	Connector: Neutrik & speakON
Network	Control Network: Compatible with standard 100 MB Ethernet
AUX Outputs	Connector: Balanced Euroblock 3.5 mm Maximum Output Level: 21 dBu
Contact Closure	Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Data	Data Connection: Euroblock 3.5 mm - Gnd, 18 V, in, out
Outputs	Fault Condition Logic Outputs: 4 x 3.5 mm Euroblock
Level Control	Remote DC: 4 x 3.5 mm Euroblock - Gnd, CV, V+ per input
Attenuation	Front panel, software, offset link group, and remote per channel Fully off = mute
Protection Circuits	Inrush current limitation, temperature monitoring, output over-power protection, and mains fuses
Cooling	Continuously variable temperature controlled axial fans
Environmental	Non-condensing 32 to 113°F (0 to 45°C)
Dimensions	19.0 x 3.5 x 16.8" (48.3 x 8.9 x 42.8 cm)
Weight	32.4 lb (14.8 kg)
Packaging Info
Package Weight	32.5 lb

4-Channel high-output amplifier with programmable output on each channel (High-Z or Low-Z, selected via rear panel DIP switches)

Power-saving, Energy Management System with automatic <1W sleep-mode (defeatable)

Front panel power switch and level controls (can be disabled for security)

Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration

Remote DC level control on each input channel

Switch mode power supply automatically detects 120 or 240VAC operation

Extensive protection circuitry and continuously variable cooling fans

Multiple independent internal power supplies provide increased channel separation and reliability

Ethernet port for control and monitoring of amplifier functions, with front panel COM activity LED

Serial data port for use with Ashly remote control devices, or optional RS-232 converter for third party controllers (not included)

Use Protea software to remotely disable all front panel controls, including the on/ off switch, for a tamper-proof installation

Offers 32-bit SHARC DSP processing with 48 & 96 kHz sampling

Built-in signal generator for test tone and noise-masking

Swept load impedance monitoring available on each amplifier channel output

Real-time clock with event scheduler

Instant standby mode that can be triggered by contact closure, software control, or event scheduler for reduced power consumption

Programmable power-on delay

Preset recall via contact closure, software control, remote control, or event scheduler

Aux preamp outputs, and fault condition logic outputs

Optional Cobranet or Dante network audio and AES3 digital audio input with pass-through

Dynamics, gain, equalization, FIR filter ready, 2 x 4 or 4 x 4 matrix mixer, crossover, delay, metering, and signal generator functions for test and noise masking applications

Precision swept load impedance monitoring of each amplifier channel for quick and easy diagnosis of sound system problems remotely via Ethernet

Neutrik Combo XLR - 1/4" TRS jack plus Euroblock input connectors

Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability

Neutrik powerCON detachable AC mains connector

Made in USA

Related Questions and Answers

Q: 1. Can two amps be joined together to fit in a 1RU rack space with the included hardware?

A: Yes, two of the QSC SPA2-60 2-Channel Power Amplifier (60W) can be mounted side by side in one rack space. Installation instructions for this configuration can be found in the installation guide here: https://bhpho.to/4aKF5J4

Q: 2. Does it have fans to keep it cool?

A: Yes the Yamaha PX8 amplifier has cooling fans.

Q: 3. Why is this Marantz amplifier so expensive and it does not even have decent 4ohm performance. A lot of metal though.

A: This amplifier is not a stock item, and it is currently selling for list price. It's not for everybody.

Q: 4. Will this amp work with Bose Virtually Invisible 191 Speakers? Some list this speaker at 6 ohm's. The spec for this amp list 4 or 8 ohm's not 6.

A: Yes, this would be compatible. Bose lists the specs of the Virtually Invisible 191 speakers as 100w @ 8 ohms, but this amplifier would be compatible with speaker that are 4 - 8 ohms.

Q: 5. how do you drive 25v output?

A: Not sure what you are referring to. Please send us your questions via e-mail: AskBH@a href= http://BandH.com target= _blank BandH.com/a

Q: 6. can i install a separate volume control in the wall in another room ? if so is there a spec?

A: You can as long as it's able to handle the wattage. In this case it would be 100w per channel.

Q: 7. Can this be powered by Ac input 220v?

A: This device 120V AC/60Hz only.

Q: 8. Does the Ashly ne8250PE amp come with all the Euroblock connectors or do they have to be purchased seperately?

A: The Euroblock inputs are embedded into the rear chassis of the component. No Euroblock connectors ae included as separate DIY items for crimping/soldering onto your own wiring.

Q: 9. If your amplifier is CE certified can I get testimony from you to that effect?

A: You can find Ashly's certifications by following the link below, and clicking on the 'features' tab. https://ashly.com/tra-convection-cooled/

Q: 10. how do you rack mount this amp?

A: Use a rack shelf.

Blue room	25/09/2024
[32.5 lb] In today’s immersive sound world i.e. Atmos, DTS:X and Auro-3D, the MM8077 is a perfect product for your amplifier needs. I’m very happy with this product. 5

Henry	04/09/2024
[0 to 22 dB] Great sound and quick response. Its a beautiful match to its sister pre-amps (mine is the AV7702MKII). I mostly listen to stereo music, but with the 7 channel amp, it can be excellent home theater. 5

anyonymous	29/08/2024
[21 dBu] I use the SLA-2 with a BBE bass pre-amp to run two Eminence CB15 15 bass guitar speakers. This amp has more power than I will ever need. George Red Taylor 5

Jay G	27/08/2024
[5 to 1000 ms/dB] Great clean power reliable performance. Using with Marantz 8055 5

Richard	12/08/2024
[10 kΩ] Pared this with the Marantz AV7705 processor and couldn’t be happier. Clean powerful sound driving my Boston Acoustic VR-M90’s. Have battled for 14 years with a intermittent AC ground loop hum with my former Outlaw Audio equipment. Now, no more hum! Thank you Marantz! 5

Martin A	08/08/2024
[21 dBu] Best purchase ever must have for music quality enthusiast. Having a power amp allowed me to also add in professional equalizer to my SR 5011 receiver. Provided power to drive the surround speakers to turn up the movies and music experience to another level which was unachievable with the SR 5011 receiver alone 5

Robert F	28/07/2024
[ANC: 1 to 4] Solid amp with XLR inputs. High quality. Integrates nicely with Pre-amp 5

Howard	22/07/2024
[32.5 lb] Is a great amp ? My are you asking me now I 5+ years but it working great l love it 5

CNLTDUB	18/07/2024
[1.2:1 to 10:1] I have been listening to this unit for about a year now. It's paired with Dynaudio Evoke system. I come from years of Car Audio SQ competition, and Home audio system. This has blown me away for the price vs. performance. This amp can beat the hell out of these speakers when asked...and stays poised the entire time. The SQ is amazing for the speakers price point. 5

Duke	24/06/2024
[5 to 1000 ms/dB] Great unit. I’m very happy with it. I’m running energy connoisseur speakers 5.1 system. Should I get the MM7055? 5