Neutrik XLR Female to BNC Female Adapteris a pre-wired connection point allowing you to conjoin heretofore incompatible items. In this case, you're given a rugged, die-cast shell which facilitates XLR female to BNC female connections.

Die-Cast Shell    Connection Between XLR Female and BNC Female

Related Questions and Answers

Q: 1. Can I use this to extend a SDI cable run?

A: The Pearstone BNC Female to BNC Male Right-Angle Adapter (B&H# PEABNCB1R) will connect to one female-end BNC and one male-end BNC. As such, if you somehow have an SDI cable with a female end (extremely rare) then you could theoretically use this for that purpose if the other end of that same cable is male. However, in all likelihood (you'll want to check), both of the ends of your cable are male. For that reason, you'll need a double-female connector to connect two cables that have male BNC plugs. Here's a good option for up to 6G-SDI: Pearstone BNC Female to BNC Female Adapter (B&H# PEABNCD1) https://bhpho.to/3PCtlyB

Q: 2. Is this the best option for connecting one xlr cable to another, thus extending the length?

A: Yes, the Neutrik 3-Pole XLR Female to 3-Pole XLR Male Extension Adapter is a solid option to connect between 3-pin XLR male and 3-pin XLR female connection points.

Q: 3. How long is the extension?

A: This product is 2.9 inches long.

Q: 4. Will NA3FDM fit Audio-Technica AT8646QM Microphone Shock-mount Plate?

A: The Neutrik NA3FDM should fit into the Audio-Technica AT8646QM shock mount plate, but the original connector on the plate is much different from the NA3FDM. Just be aware of the extra clearance needed behind the plate to accommodate the barrel of the male connector on the back.

Q: 5. Does any other company make such an extender in black?

A: Unfortunately, we do not currently offer an option that is a 3-Pole XLR female to 3-Pole XLR male extension adapter in black.

Q: 6. Can this connect a microphone directly to a recorder? Such as, a Lewitt 140 air to a Sound Devices MixPre 3?

A: This could work for you, but that will probably put a lot of strain on the mic connectors. Using a longer cable, and mounting the mic on a stand, grip, or boom pole - will be a much better option.

Q: 7. Neutrik NA3FDM XLR Female to I recently purchased the Male Feedthrough Adapter for Panel Mount. What type of screws are needed?

A: The Neutrik NA3FDM XLR Female to Male Feedthrough Adapter for Panel Mount requires 4-40 screws. The length will depend on your use case, but 3/8 is commonly recommended.

Q: 8. What is the ohms on this connector?

A: I am afraid that the exact Ohm rating of this connector is not listed by Pearstone. However if you must have 75 Ohm we have a similar angled connector from Comprehensive that is specifically rated at 75 Ohm and does not cost that much more. B&H # COABMBFRA will work very well for you.

Q: 9. I need to bring XLR audio directly into the Aja IO 4k (https://a href= http://www.bhphotovideo.com/c/product/1025891-REG/aja_io_4k_10_bit_4k_uhd_sd_i_o_tb_2.html target= _blank www.bhphotovideo.com/c/product/1025891-REG/aja_io_4k_10_bit_4k_uhd_sd_i_o_tb_2.html/a). Will this do the trick?I'm thinking I connect my condenser mic to a mixer where it gets phantom power, output with XLR cable to this adapter and plug this adapter directly into one of the SDI BNC connections on the IO 4k. Will that work? Thanks!

A: Sorry, but the AJA Io 4K I/O for Thunderbolt 2 B&H # AJIO4K has no analog audio input connectors, only analog outputs. In order that we may better assist you, please write us with further detail about what you want to do. provideo@bhphoto.com.

Q: 10. Will this click in to a Zoom F3? My shotgun mic won't click in and I have seen others click.

A: Yes, the Neutrik 3-Pole XLR Female to 3-Pole XLR Male Extension Adapter will be compatible with the Zoom F3's locking Neutrik XLR connectors.