Ashly Ne4400Ad Dsp With Aes3 Inputs & Dante Card

Ashly Ne4400ad Dsp With Aes3 Inputs & Dante Card

Product Code: eq147688
Availability: In Stock

$8,697.00 $10,610.34

Qty

8 reviews Write a review

Description
Reviews (8)

Control and protect your sound system with the Ashly ne4400AD, a network-enabled DSP processor that offers easy setup and control using standard 10/100 Ethernet protocol and Protea ne software. The ne4400AD features four option bays for expanded functionality. This model includes the 4-channel AES3 input card and Dante network card.

The rear panel utilizes Euroblock connectors for easy and secure wiring. Additionally, the 12V Digital Logic I/O uses a 9-pin Euroblock connector that can be assigned to trigger a preset recall or push-to-talk mic function. A 10-pin Euroblock connector is for the 5 VDC Remote Level Control, which allows for up to eight user-defined remote DC level controls.

4 Analog Inputs / 4 Analog Outputs 10/100 Ethernet and RS-232 Interfaces 24-Bit A/D-D/A Audio Resolution Extensive DSP via Protea Software Suite Easy and Intuitive User Interface Wordclock I/O Option Bays for Expanded Functionality Windows

Parameters
Frequency Response	20 Hz to 20 kHz ±0.1 dB, A>D ±0.25 dB, D>A ±0.25 dB, A>A
Dynamic Range	20 Hz to 20 kHz (Unweighted) >115 dB, A>D >114 dB, D>A >114 dB, A>A
THD + N	1 kHz, +20 dBu Analog (-1.0 dBFS Digital) <0.001%, A>D <0.002%, D>A <0.002%, A>A <0.00001%, D>D
Latency	48 kHz 1.42 ms, A>D 0.90 ms, D>A 2.21 ms, A>A 0.10 ms, D>D 96 kHz 0.71 ms, A>D 0.45 ms, D>A 1.11 ms, A>A 0.05 ms, D>D
Wordclock	Input/Output Type: 75 Ohms BNC Lock Range: 48 kHz ±4%, 96 kHz ±4% Input Impedance: Selectable 75 Ohms or High Impedance Input Voltage Range: 1.0 to 7.0 Vpp Output Impedance: 75 Ohms Output Level: 5.0 Vpp Nominal, Unterminated
Master Clock	Sources Audio Network Wordclock AES3 Internal Crystal Clock Modes Prioritized Auto Switching Manual
Inputs	Analog Line Input Type: Active Balanced Euroblock Input Impedance: 20 Kilohms Maximum Input Level: +20 dB AES3 Digital Input Type: Transformer Balanced Female XLR Input Impedance: 110 Ohms Max Input Level: 7.0 Vpp
Outputs	Analog Output Type: Servo-Balanced Euroblock Output Impedance: 20 Ohms Maximum Output Level: +20 dBu AES3 Output Type: Transformer Balanced Male XLR Output Impedance: 110 Ohms Maximum Output Level: 5.0 Vpp
Other Connectors	10/100 Ethernet Port RS-232 Port Remote Level Control Logic I/O Data In/Out Ports On/Off Switch
Environmental	40 to 120°F / 4 to 49°C Non-Condensing
Power Requirements	90 to 240 VAC, 50/60 Hz 70 W Maximum
System Requirements	Computer Running Under Windows Vista, 7, 8, 10
Dimensions (WxHxD)	19 x 8.5 x 3.5" / 483 x 216 x 89 mm
Weight	10.5 lb / 4.8 kg

CobraNet, Dante, AES3, Mic Input options
10/100 Ethernet and RS-232 computer interface standard
Extensive DSP available
Easy and intuitive user interface
24-bit A/D–D/A audio resolution
32-bit SHARC DSPs
Sample rates of 48 and 96 kHz
Hot-plug software control
Automatic DHCP network IP configuration
Butterworth, Bessel, Linkwitz-Riley, and Notched-Linkwitz-Riley filters
FIR filter capability
Advanced automatic feedback suppression
Wordclock input and output
Euroblock connectors for audio, preset recall, DC remote level control and data in/out
Remote controls for level, logic I/O and programmable functions
Third-party control friendly, input and output metering, multi-level security

Input source selection
Brick wall limiter
Compressor
AutoLeveler controls
Ambient noise compensation (output only)
Ducking (high/low priority, trigger, filibuster, ducked program)
Gate
Advanced gate controls
Gain
EQ:
- 31-band
- Parametric 2, 4, 6, or 10 band
- High/Low Shelf 6/12 dB per octave
- All-Pass
- Variable Q HP/LP
- Notch/Band-Pass
Feedback Suppressor (inputs only and 48 kHz sampling rate)
Crossover: 2-, 3-, 4-way crossover and High-Pass/Low-Pass filters
Delay:
- Input time, distance, and temperature at 48 kHz sampling rate
- Input time, distance, and temperature at 96 kHz sampling rate
Audio metering tool
Signal Generator Tool (pink noise, white noise, sine wave)
Matrix mixer
Processors

All programming is accomplished using standard 10/100 Ethernet or RS-232 protocol and Protea ne software on a PC platform. Hot-plug software control allows you to plug any function into any channel block, even when running live audio with no recompiling necessary. Automatic DHCP network IP configuration reduces network set up time. Multi-level software security with password access assures you a tamperproof audio system.

Related Questions and Answers

Q: 1. can you hook a power amp to the mm2000?

A: I don't think so. It has a built-in amp.

Q: 2. .....I just read the description: it says Bass, Treble and Balance Controls YET as I look at the face of this unit, NO bass, NO treble and NO balance controls? What gives? Mistake or are the controls in the back or ...what??....

A: It is available from the Audio Function button and visibly adjusted via the LCD screen MENU.

Q: 3. Playing MP3 from USB or SD in shuffle mode, then turn off the unit. When turned on again, will it play the same song or restart at #1?

A: When turning off the unit, the song position will be reset to the start of song # 1.

Q: 4. I just read Bass, Treble, and Balance Controls YET if you look at the photo of the face --NO bass, NO treble, NO balance controls? Where are they?

A: To get to change the Bass, Treble, Balance, there is a button labeled Audio Functions press it and it goes thru all three choices to you can change it to how you like it.The EQ button gives you optional pre set sounds Classical, Flat, Pop, Jazz, JazzRock sounds best to me.I just wished it allowed 2 sets of speakers. I always make sure I turn the speakers down to off before I snap it off or on, so I don't blow anything..

Q: 5. Putting sound system in gym I need to run 8 speakers loud?

A: Please reach out to us directly at audio@bhphoto.com , so we can help recommend an amp based on the specific speakers you are using.

Q: 6. The specs say it puts out 1,200 watts. We know that's not true. Does anyone know the real constant power output?

A: The manufacturer has not published any detailed power specifications. I would assume an RMS or continuous rating of less than 120 watts at 4 ohms.

Q: 7. how does the loop fuction in and output work?

A: The loop in and out is used to integrate an external signal processor such as an equalizer with the MM2000. The output of the external device is plugged into the loop in and the loop out is plugged into the input of the external device; thus creating a loop.

Q: 8. dose it have a remote control?

A: The MM3000 does not have a remote available.

Q: 9. what is the speaker output OHMS required for each channel ?

A: This mixer/amp can handle speakers between 4 and 16 OHMS.

Q: 10. what is the speaker output OHMS required?

A: The MM3000 will support speakers rated from 4 to 16 ohms.

Mark	15/09/2024
Since Presonus does not provide Dante capability in their StudioLive mixers, this adapter is a good way to add it for at least four output streams from one of the mixer's mix busses. Great for sending Dante streams to remote powered speakers, saving mixer analog outputs for other uses. 5

Peter	23/08/2024
I use this with a Roland M200i digital mixer to provide an audio feed to a livestream PC. Using the LAN saves adding an analog adapter to that PC. 5

Ioannis	23/08/2024
Adding this card to Ashly Digimix24 will release the full power of the mixer, allowing you to use all input/output channels in your PC/DAW/iPad. It works flawlessly, and my only minor complaint might be that the latency is not as low as e.g. my RME UCX, but still in the very close to it and in the unnoticeable side of things (about 5-6mS full duplex). This also has to do with the sample rate used (48KHz), while UCX can go up to 192KHz, which reduces latency further. All things considered, I suggest Ashly USB-32 without a second thought! Service of B&H was also awesome, arriving to the other end of the world (New Zealand) in very short time and without issues! 5

Gastone	28/07/2024
Very fast shipment. All OK! 5

Robert	17/07/2024
Easy to implement, Works as expected. Just remember it's PoE so plan accordingly. 5

Matthew	07/07/2024
This adapter saved me $1500 dollars from buying a Q-Sys I/o frame. Works as it should. 5

Rick	24/05/2024
Audinate Dante AVIO 2x2 AES3/EBU I/O Adapter for Dante Audio NetworkS works perfectly. Just add to your Dante network, POE switch or injector required, route audio in Dante Controller and you are set! Great economical solution when you need a pair of AES3 audio inputs and/or outputs. Highly recommended. 5

Rob	21/05/2024
Perfect for adding one AES device at 96k to your Dante Network. I bought 2 of these, one for each of my Bricasti Reverb units so I could put them on my Dante network. Worked flawlessly. 5