Sporting a lightweight and compact design, the TechLok LapLok Laptop Anti-Theft Security Devicekeeps your computer safe and secure, preventing physical theft thanks to the enhanced locking mechanism and sturdy construction.

Leveraging a lockable C-clamp design, the main component connects to a table while a tab secures your laptop to the security device. Easily set and enter your custom passcode so you can unlock the clamp at your leisure and ensure no one else easily removes it. Various LEDs ensure the status of the lock while keeping buttons visible. Soft rubber pads keep the device secured to your table without damaging the surface. You also get a built-in anti-theft motion sensor and an 80 dB alarm, notifying you if someone was attempting to remove the LapLok.

Compatible with All Laptops    Anti-Theft Motion Sensor    Clamp Design    Integrated Code Buttons    80 dB Alarm

Related Questions and Answers

Q: 1. Does this take classic arca swiss plates? WHat is the load capacity of the clamp?

A: No it will not take the classic series plates. I believe it is rated for 75 lbs

Q: 2. is this standard Arri-rosette mount on this? thanks much

A: The rosette on the DJI Ronin-M Mobile Device Holder is not an ARRI standard rosette.

Q: 3. What is the maximum width for plates that can be held in this device?

A: The plate must fit the dovetail slot in this Quickset Device. I've found that the Quickset lever won't lock unless I had a camera plate that fit into the dovetail slot properly. I use an Arca Swiss 802260 Monoball Fix 32 Camera plate (the B&H # on my order was ARSF32C) with the Quickset Device - there are other Arca Swiss Monoball Fix 32 plates available as well. I've measured the 802260's camera plates dovetail with calipers and at the 'neck' of the dovetail, its 19.07mm and at the base of the dovetail 25.85mm The height of the dovetail from bottom of the dovetail base to the bottom of the camera plate is 5.45mm. When the Quickset Device has nothing in the dovetail slot and the lever is in the closed/latched position, the opening is 23.04mm (this measurement is at the location where the camera plate's dovetail neck would fit. When I push the lever as far open as possible, the opening is 25.12mm wide -- but the lever won't close if you fit something this big into the Quickset Device.

Q: 4. is This handgrip comes with an ARRI standard rosette (31.8mm diameter) ?or what is the diameteralso is this a M6 thread mounting hole ?

A: According to Movcam, their rosettes are Arri compatible with M6 thread and 31.8mm diameter.

Q: 5. Does the end of this grip (the interior aluminum post) have a -20 thread tap? If I wanted to change the grip, is that possible?

A: The Movcam Anti-Skid Handgrip does not have a 1/4"-20 thread anywhere on it. It will attach via a rosette at its end. We do not sell replacement grips for this handle.

Q: 6. can this be installed directly on arca-swiss monoball p0 ballhead? is this compatible with universal arca-swiss standard plates?

A: Yes, you may use the Arca-Swiss MonoballFix Quickset Device listed above on the top of the Arca-Swiss Monoball P0 with Panning System, B&H # ARMPOPS. It is compatible for use with standard Arca-Swiss quick-release plates.

Q: 7. Got a photo of this attached to 386B-1 Nano Clamp?

A: No we don't

Q: 8. Does this take genral Arca-Swiss compatible plates?

A: The Arca-Swiss MonoballFix Quickset Device does not use standard Arca-Swiss plates. You need smaller than normal, MonoballFix camera plates like the Arca-Swiss monoballFix Cameraplate 48 Universal. Here is the link: https://bhpho.to/3vqjTqa

Q: 9. How is this best used?

A: The Pelican Anti-Corrosion Kit is an anti-corrosion kit that helps protect items such as stored firearms and critical electronics from airborne contaminates that can cause corrosion for use inside a Pelican case. The color changes on the indicating foam to let you know when the film is ready to be replaced and can no longer absorb corrosive elements. The foam also acts as a secondary corrosion filter.

Q: 10. will this grip remotely operate my camera ?

A: No, it will not. It is just a handle for keeping your rig steady. For your reference, I used this on my FS700 and it does not attach properly. Check that your ARRI rossette on your rig or camera has a deep screw hole. The FS700 ARRI rossette is shallow and so this handle does not attach without some modification.