Make sure you can get your ASF-1 MKII Hydrophone to the right depth while staying connected with this 328' Ambient Recording AHK-100-MKII Hydrophone Cable 328ftfrom Ambient Recording. This 328' cable comes on a cable drum for easier management.

For ASF-1 MKII Hydrophone    AHS Underwater Connector to 3-Pin XLR

Related Questions and Answers

Q: 1. Can it be use with a RED dragon and Sounddevice mixpre3 ?

A: I'm sure you can feed the TC in on the Sound Devices with the cable included with the nano lockit. However, the Red cameras need a proprietary adapter cable to feed TC in through a BNC connector. That means you'd also need the lemo to BNC output cable for the nano lockit. Hope that makes sense!

Q: 2. You can get two Atomos UltraSync Ones for less than this, and those have displays. Is there some advantage to NanoLockit?

A: Professional gear is more reliable and has the features professionals need. The Ambient Recording ACN-NL-L NanoLockit Miniature Timecode Synchronizer with Logging Feature (2-Pack) is professional gear.

Q: 3. Does this require an audio recorder or some other device to send timecode to it?

A: The Ambient Recording NanoLockit Miniature Timecode Synchronizer with Logging Feature generates its own timecode.

Q: 4. Can you purchase/add additional units (Lockits) for multi cameras, or do they need to be purchased in pairs (send & receive)? I would like to buy the 2 pack now and buy another unit or two later when needed to sync multi cams/audio recorders.

A: Yes it is possible to get a single Lockit if necessary. Ambient Recording NanoLockit Wireless Timecode Generator (Single) B&H # AMACNNL MFR # ACN-NL

Q: 5. Can timecode work on two cameras that cannot be set at the same frame rate?

A: Timecode cannot work on two cameras with different frame rates.

Q: 6. Can the battery be user replaced when necessary?

A: The battery is built into the NanoLockit and not user serviceable.

Q: 7. Will this device accept an SDI signal as a genlock input, broadcast this over ACN, and output a wordclock referenced to it? I see lots of discussion of genlock output, but not input. I have a camera without genlock, and I want to avoid pops when combining HDMI + AES - SDI. Therefore I want to synchronize the audio ADC to the un-genlockable camera.

A: no this device will not work as a genlock for a camera without genlock, it's base/fundamental mode of synchronization is time code

Q: 8. I am looking for a good solution to mount this to a camera. Is there a 1/4-20 mount (or similar) for this?

A: There is no mount made specifically for the Ambient Recording ACN-CL. Often times people use velcro patches or ties to fasten the unit to a rig. Alternatively, you can look at some of the 1/4-20 clamps we have. I recommend using a patch of velcro though.

Q: 9. for virtual production volumes, can the device be synchronized to an evertz 5700 and then run standalone as a timecode and genlock generator on camera? also maintaining genlock that would normally come from evertz?

A: With the LTC output of the Evertz 5700, you can sync the Ambient Recording ACN-CL Lockit Compact Wireless Timecode Synchronizer in TX mode. As a TX master, the Lockit will adapt to the speed of the LTC signal, and it will regenerate and broadcast the time code and sync to all of the following ACN units. For virtual productions, I would recommend using the Lockit+ (B&H # AMACNLPE) as the TX master as it gives you more insights about the current sync status in its web interface.

Q: 10. Can this use with C300MKII and Sound Devive Premix6 as the C300mkII has a timecode input with sdi cable, does NanoLockit has a SDi adapter?

A: According to Ambient: The NanoLockit does not have a SDI port. To supply the Canon C300 MKII with time code, you have to use the camera's BNC TC port. For syncing up this camera with the new Sound Devices MixPre-6, you will need the ACN-ML-D double pack and the LTC-OUT cable. Ambient Recording LTC-OUT Lockit Time Code Out to BNC / L5P-BNC B&H # AMLTCOUT