ThisMilos QCM41 4-Way Cross Piece for Trussfrom Milos QCM41 4-Way Cross Piece for Trussallows 4 sections of M222 truss to connect and extend from a central point.

Connects 4 Truss Sections

Related Questions and Answers

Q: 1. How much weight can it handle?

A: The capacity of the corner is dependent on the horizontal and vertical span that it will be connected to. How are you using it and how wide and the tall if the truss that it is being connected to? How much weight do you need to load on the truss system?

Q: 2. What it the max hanging weight limit on this

A: The Milos QuickTruss ULTRA Display Square Truss Kit (13.0 x 13.0') technically, if the system was being used indoors, on level ground cable of supporting the loads being applied, then the system could support as much as 2,900 Lbs. per 4m side, for a combined load of 11,600 Lbs. on the total system. This is based on a uniformly distributed load across each of the 4m spans of truss (so things like cables, drapes, etc.). If a large point load is preferred then the user could apply a single point load of 2,500 Lbs. anywhere on each side (so 10,000 Lbs. total if that load was applied to each of the 4 sides). This also assumes that the loads can be applied in such a way as to not damage the members of the truss (suitable clamps, slings, etc.). Outside use there are way more variables and best is to contact the lighting department in chat.

Q: 3. The description lists the Conical connector system as being available separately, but the In the Box section lists the truss coming with three connectors and the appropriate pins and clips. Do I need to purchase a connector set to join two truss sections?

A: To connect another M222 section to this section, you only need 2 conical connectors. Having said that, this section includes 3 connectors, two for combining the sections and one spare.

Q: 4. I see the spec's say DCI 4K(4096 x 2160) but does it do UHD 4K (3840 x 2160) ?

A: Hi Mike, This is Jules from product support at Symbiosis, Decimator's master distributor for the US. The 12G-Cross supports all SMPTE formats up to and including 4K (4096) 60p. This includes all SMPTE compliant UHD formats of 3840x2169 up to 60p. It also supports a range of VESA formats. I hope this helps. Kind Regards Jules

Q: 5. What is the equipment weight capacity for this rail?

A: You're safe up to 5 pounds. Anything more than that you might want to check with Novoflex: mail@NOVOFLEX.com

Q: 6. Does this include a sensor cleaner?

A: No, the B+W 5-Piece Cleaning Kit does not include a sensor cleaner.

Q: 7. Does it pass over the Canon or ARRI recording trigger after conversion?

A: No, the DECIMATOR 12G-CROSS 4K HDMI/SDI Cross Converter does not pass recording triggers through the converter at this time.

Q: 8. Can this scale an HDMI in to HDMI out? (With no SDI connections) We need to go from 1080p60 HDMI to 2160p29.97 HDMI.

A: The Decimator 12G-CROSS 4K HDMI/SDI Cross Converter with Scaling and Frame Rate Conversion, is able to convert any SMPTE formats from HDMI to HDMI or SDI output, and can convert an input of 1080p60 through HDMI to an output of 2160p29.97 HDMI.

Q: 9. What size is the rod here? 15mm or 19mm?

A: The cross pipe on this unit is 19mm.

Q: 10. What is the length of each section of truss? can the parts be reconfigured?

A: The manufacturer does not specify the lengths of each section. Truss can be configured in many ways, but this kit was designed around a specific purpose. Other configurations might require additional clamps, clips or other components.