This black 160-liter capacity Eylar Crossover Roto-Molded Equipment Case Set Blackis built lightweight and strong, making it perfect for outdoor productions, travel, or adventure. Its stackable design allows you to stack two or more of these cases. Strapping anchor slots on all four sides allow the cases to be tied down for secure transport with top access to the lid. This case features padded side handles, a 220-pound load capacity, water resistance, and heat resistance up to 212°F.

Meets TSA Requirements    220 lb Capacity, Padlock Fitting    Strapping Anchor Slots    Heat Resistant up to 212°F

Related Questions and Answers

Q: 1. Anyone know if it will fit the Westcott 32inch Rapid Box duo collapsible beauty dish with a compact tripod? Is it perfectly cylindrical inside?

A: It's more of an octagon.

Q: 2. Will this fit a 40" c-stand with the base detached?

A: It will not fit a 40" c stand even with the base removed.

Q: 3. Does this have a strong plastic or PBA type smell when purchased new?

A: There is little to no odor emitting from this case when it is new.

Q: 4. Will a Sachtler Flowtech 75 fit in this case?

A: Yes, the Sachtler Flowtech 75 MS Carbon Fiber Tripod with Mid-Level Spreader and Rubber Feet (BH #SA4585) will fit inside the SKB Roto-Molded Tripod Case with Wheels (37"), though you may want to consider a shorter case, as the tripod is 26.8" in height when closed, so in this case there would a good bit of extra room. However, should you also have a fluid head mounted to the legs the height of the head should also be considered.

Q: 5. I am interested in the SKB Roto-Molded Tripod Case (24 Tall). Would two tripods (each under 23 inches tall) and two ball heads not attached fit in this case?

A: Hi Lynette, It depends on the diameter of the tripod legs to judge if you have enough room for the two ball heads. If you have tripods for still cameras most likely they will fit as they tend to be smaller than tripods for video. Two tripods each under 23 inches should fit no problem unless the diameter of the legs closed is over 6 per tripod. To verify you could use a piece of gaffers tape and tape the the two tripods together and measure. Thank you,Will

Q: 6. Is there a way to lock the lid on? I'd like to be able to lock the case and check it on a flight.

A: From the looks of it the fasteners are only buckles and does not appear to lock on this model.

Q: 7. Are the size specs listed on B&H for the 34 case accurate (38.25 x 12.75 x 14.00 and 15lbs)? As stated, it would appear this is slightly bulkier and heavier then the 37 model.

A: Hi Shaun, That is correct. The reasoning for that is the 37 tripod case (1SKB-R3709W) has a diameter of 9 vs. the 1SKB-R3411W which has a diameter of 11 . In production they used a touch more plastic in the 1SKB-R3411W which put the weight of the 1SKB-R3411W tripod to 15 lbs. Thank you,Will

Q: 8. Is the interior dimensions measured with or without the foam?

A: That is with the foam.

Q: 9. How much space does the padding take up on the inside? My tripod measures 41".

A: This case has 9 x 42" available, so a 41" tripod will fit.

Q: 10. Which one do you recommend for the PED C III pedestal?

A: Sachtler recommends using the following case for the PED C III. Sachtler Cover EFP 2 Hard Shipping Case BH #SACEFP2 • MFR #9315 https://bhpho.to/3Fplku9