This gray 160-liter capacity Eylar Crossover Roto-Molded Equipment Case Set Grayis built lightweight and strong, making it perfect for outdoor productions, travel, or adventure. Its stackable design allows you to stack two or more of these cases. Strapping anchor slots on all four sides allow the cases to be tied down for secure transport with top access to the lid. This case features padded side handles, a 220-pound load capacity, water resistance, and heat resistance up to 212°F.

Meets TSA Requirements    220 lb Capacity, Padlock Fitting    Strapping Anchor Slots    Heat Resistant up to 212°F

Related Questions and Answers

Q: 1. Are the size specs listed on B&H for the 34 case accurate (38.25 x 12.75 x 14.00 and 15lbs)? As stated, it would appear this is slightly bulkier and heavier then the 37 model.

A: Hi Shaun, That is correct. The reasoning for that is the 37 tripod case (1SKB-R3709W) has a diameter of 9 vs. the 1SKB-R3411W which has a diameter of 11 . In production they used a touch more plastic in the 1SKB-R3411W which put the weight of the 1SKB-R3411W tripod to 15 lbs. Thank you,Will

Q: 2. I am interested in the SKB Roto-Molded Tripod Case (24 Tall). Would two tripods (each under 23 inches tall) and two ball heads not attached fit in this case?

A: Hi Lynette, It depends on the diameter of the tripod legs to judge if you have enough room for the two ball heads. If you have tripods for still cameras most likely they will fit as they tend to be smaller than tripods for video. Two tripods each under 23 inches should fit no problem unless the diameter of the legs closed is over 6 per tripod. To verify you could use a piece of gaffers tape and tape the the two tripods together and measure. Thank you,Will

Q: 3. Is the interior dimensions measured with or without the foam?

A: That is with the foam.

Q: 4. How much space does the padding take up on the inside? My tripod measures 41".

A: This case has 9 x 42" available, so a 41" tripod will fit.

Q: 5. Length

A: The Specifications tab states the exterior dimensions for the SKB Roto-Molded Tripod Case with Wheels (37 Tall) measures 12.5 x 40.25 x 11.0 .

Q: 6. Will I be able to check this bag and not pay oversize fee at airport. Most airlines use L, W, H, total of 62 inches and under as not oversized. Also I have a 38 slider, will this fit in the case?

A: This design is an extremely annoying 1.5 beyond the oversize limit. I've checked it twice without being charged anything extra. But I'm just waiting for a stickler check-in agent to ruin my streak with a $200 oversize fee...

Q: 7. Is there a way to lock the lid on? I'd like to be able to lock the case and check it on a flight.

A: From the looks of it the fasteners are only buckles and does not appear to lock on this model.

Q: 8. Will this fit Sachtler Video 18 S2 Fluid Head & Speed Lock CF Dual-Stage Tripod System B&H # SAS18S2SM?

A: Yes, it sure will.

Q: 9. What are the measurements??

A: The SKB 1RMM32-DHW is designed specifically for the Midas M32. SKB offers the Exterior dimensions only. Length: 44.25 in (112.40 cm) Width: 35.75 in (90.81 cm) Depth: 14.75 in (37.47 cm)

Q: 10. How thick are the walls of this case? It look flimsy and it feels that this model is meant to protect a bag for golf clubs? If I check this light stand case, with under 50lbs of tripods and light stands, will it arrive to my destination in tact? I'm concerned if dropped, one of the light stands will puncture through the case.

A: The light stands and tripods would not likely puncture the case. The case is not padded so the bigger concern would be the stands and tripods grinding against each other.