Enjoy stereo sound with the Pyle Pro PT270AIU.5 Receiver. Connect up to two pair of speakers with up to 300 watts of total power available. You can also connect up to two subwoofers with independent volume control. Listen to the built-in AM/FM radio, connect devices via RCA input, and playback MP3s from a USB flash drive or SD card. A docking station is available on the top of the unit with a 3.5mm male connector to playback from iPod/MP3 players. The PT270AIU.5 also has two 1/4" microphone inputs, ideal for karaoke nights or hosting events.

Up to 300 Watts Total Power Output    2.2-Channel Configuration    Built-In iPod/MP3 Player Docking Station    AM/FM Radio Tuner    Stereo RCA, USB & SD Card Inputs    2 x RCA Subwoofer Outputs    2 x 1/4" Microphone Inputs    Separate EQ for Main & Microphone    Separate Subwoofer Gain Controls    Digital LCD Display

• Auto station seek
• 50 radio station presets
• AM/FM quartz synthesized tuner
• Digital flourescent ouput display meter
• Microphone volume, tone, and echo controls

Related Questions and Answers

Q: 1. What is the continuous power (aka RMS) and value for each channel?

A: The Pyle PTA24BT runs approximately 100W RMS.

Q: 2. Can the Bluetooth on this receiver connect to my Pyle soundbar, PSBV200BT ? and if it can how ?

A: No, the Pyle Pro PT272AUBT Stereo Receiver with Bluetooth (B&H # PYPT272AUBT) does not have a Bluetooth transmitter and cannot connect to the Pyle PSBV200BT Soundbar.

Q: 3. I would like to hook up 12 outdoor speakers to this unit and a basic sub. What are the maximum watt speakers can I use? Can you suggest a couple of speakers that would be suitable.

A: The max wattage is 750watts. As long as you dont exceed that rating any 4-8ohm speaker should work fine.

Q: 4. Can this be triggered to power-up (or shut-down) once a streaming signal comes/if a signal comes from wifi-streaming unit?

A: The Pyle Pro PTA62BT 6-Zone Stereo Receiver with Bluetooth BH #PYPTA62BT will not have any trigger functions.

Q: 5. would this stereo receiver work well paired with a set of CR5-XBT stereo monitors?

A: Yes you can use a stereo pair of RCA cables (BH #KOSRC4006) to connect the Pyle PDA6BU to the Mackie CR5-XBT monitors.

Q: 6. Can you control which channels play using the remote control?

A: Yes, the remote control included with the Pyle Pro PTA62BT 6-Zone Stereo Receiver with Bluetooth (B&H # PYPTA62BT) can be used to select the audio source with the MODE button, labeled as item 5 on page 5 of the manual: https://bhpho.to/3VOmupH

Q: 7. Is the 750 Watts = to 125 Watts per speaker channel?

A: This is a 6 zone/12 channel amplifier. Max power is 750 watts divided by 12, so 62.5 watts per channel. I would like to note this is maximum power and it is not recommended to run any amplifier at continuous full power. I would recommend this product for use with speakers that require 40 watts RMS per speaker or less.

Q: 8. How much clearance will this need for proper ventilation/cooling? The project I'm working on probably won't afford much space.

A: Pyle Pro does not specify clearance for installation, other than *Use the amplifier only in well-ventilated installations. You would want to allow some airflow to keep the component from over heating. An inch on all sides should be sufficient, but use your own judgement according to your particular setup.

Q: 9. HOW DO YOU GET THE RADIO WHEN SCANNING FOR STATIONS TO STOP ON THE ONE YOU WANT?

A: Use the remote to set-up your presets.

Q: 10. Can I use bare speaker wires to connect to PDA6BU?

A: Yes, the Pyle Pro PDA6BU Stereo Receiver with Bluetooth BH #PYPDA6BU can accept bare speaker wire.