The Gra-Vue XIO 9001VSD-RC SD-SDI Signal Distribution Amplifierfrom Gra-Vue XIO 9001VSD-RC SD-SDI Signal Distribution Amplifierprovides dual SD-SDI signal inputs, and distributes each of them to 3 outputs with re-clocking. This distribution amplifier card is designed to be mounted vertically in a 3RU frame. The card supports SD-SDI and ASI input signals with embedded audio and automatic input detection of 525i 60 and 625i 50 resolution.
The XIO 9001VSD-RC Distribution Amplifier provides automatic signal equalization and re-clocking when long cables are used. This improves the signal quality and reduces signal loss caused by long distance transmission of input sources. The LED lights on the module indicate the status of input signals and power supply. The distribution amplifier also supports SNMP and can be real-time managed and monitored via the XIO NET Network Management Module (sold separately) via Ethernet.

2 SD-SDI input signals, each one distributed and re-clocked to 3 SD-SDI output signals

Supports automatic input detection of 525i 60 and 625i 50

Supports SD-SDI signals with embedded audio

Supports processing and distribution of ASI signals

Supports hot swap plug

Broadcast quality with inner 10-bit processing

Features LED lights which indicate the status of signals and power supply

Supports SNMP, and can be real-time managed and monitored by XIO NET (sold separately) via Ethernet

Mounts vertically in a 3RU frame

Related Questions and Answers

Q: 1. Can this be used to pass through tri-level sync for Genlock purpose? Thanks!

A: Yes, the Kramer 1 x 20 Composite/SDI Video Distribution Amplifier would be able to distribute Sync to up to 20 sources.

Q: 2. does include the power supply?

A: Yes, the attached power adapter is included in the box.

Q: 3. What is the delay in the video signal when switching from signal 1 to signal 2?

A: The Freakshow HD 2x4 12G-SDI Switchable Reclocking Distribution Amplifier has a couple of milliseconds of delay. There will be a slight glitch as you switch.

Q: 4. Will this pass control data (focus, zoom, talkback) to my Blackmagic studio cameras?

A: Yes, the AVMATRIX 1x4 3G-SDI Distribution Amplifier will pass control data to your Blackmagic Design Studio Camera.

Q: 5. It seems like this would work with a laptop. One output going to a video switcher and the second to a projector. Has anyone tried the Kramer DA in this type of workflow? Thanks!

A: Yes, this will work for that set up.

Q: 6. This Kramer claims to boost HDMI signal to increase cable length. To what length? From reviewer comments it seems the cable can additively play a part in boost distance (ie boosted distance + cable capability = total distance).

A: Absolutely. I would not consider a DA a booster but only a DA. For installation I would install the DA as close to the source as possible, no more than a 6' cable and then no more than 50' cable on each output. It is very important to use use high quality cables with any HDMI installation. If you need to go further consider using a twisted pair Rx/Tx setup for best results.

Q: 7. Is there a way to output both sources at the same time Creating 2 inputs with 3 outputs each

A: We’re afraid not. It has an A/B switch to select with SDI input you use for the outputs of the DA. You cannot split it out in that way.

Q: 8. What is the reason for two power inputs?

A: The AVMATRIX SD1151-12G 12G-SDI 1x5 Reclocking Distribution Amplifier has two power inputs for power back up redundancy.

Q: 9. Does this accept 3G level A and Level B? Any compatibility issues between Black Magic or Barco gear?

A: The AVMATRIX SD1151-12G 12G-SDI 1x5 Reclocking Distribution Amplifier will support both level A and level B SDI signals. There should be not compatibility issues when pairing the AVMATRIX SD1151-12G 12G-SDI 1x5 Reclocking Distribution Amplifier with other brands like Blackmagic or Barco.

Q: 10. Can this be used to pass tri-level sync for Genlock?

A: The Kramer 1 x 20 Composite/SDI Video Distribution Amplifier cannot be used to pass tri-level sync for genlock.