This 1 to 11-stop, 72mm K&F Concept C-Series Variable ND Lens Filter 72mm 1-11 Stopfrom K&F Concept C-Series Variable ND Lens Filter 72mm 1-11 Stopis a circular, variable neutral density filter from K&F's Classic Series, also referred to as the C-Series.

Variable 0.3 to 3.3 Optical Density

Related Questions and Answers

Q: 1. Will this fit the Canon RF 24-240mm? looking for an alteritive to spending $40.00 on the Canon.

A: Yes, you can use that hood.

Q: 2. Will this hood work with a 28mm lens on a full-frame Nikon dlsr without vignetting?

A: This lens hood would not vignette on a 28mm lens mounted on a full frame camera when it is rolled back.

Q: 3. Does this fit the FUJIFILM XF 10-24mm f/4 R OIS Lens?

A: Yes, the Heliopan 72mm Long Metal Lens Hood will technically fit the 72mm threading on the FUJIFILM XF 10-24mm f/4 R OIS Lens, but the hood would cause severe vignetting until 24mm focal length. A much better hood to use would be Heliopan 72mm Short Metal Lens Hood: https://bhpho.to/2JgBbN1 one will still see vignetting but just from 10-20mm.

Q: 4. Does this fit the older model Nikon 2.8 180mm manual lens?

A: If you are referring to the Nikon AF NIKKOR 180mm f/2.8D IF-ED Lens (B&H # NI18028DEDAF), or if your lens uses 72mm filters (as the Nikon AF NIKKOR 180mm f/2.8D IF-ED Lens does), then yes, the Nikon 72mm Snap-On Lens Cap would be compatible for use with your lens.

Q: 5. I use a Sensei 58mm to 72mm adapter ring to mount 72 mm filters on my Lumix 12-35 lens. This works fine, except I cannot use the original lens hood and the front glass is exposed to direct sunlight. Will this lens hood feel the bill, without vignetting? Thanks in advance.

A: I did have some problems with the tulip design. It did show up in the picture.What I have to do is check the picture out before taking to make sure.

Q: 6. Could this be used as a substitute for the SONY RX10-IV hood? The hood included with the camera attaches easily but is so hard to remove I'm concerned about damaging the mechanism.

A: The Sensei 72mm hood will fit the RX10 camera but since this hood is not made for the lens on the RX10 Mark 4, it is possible the hood might vignette the lens or allow a flare. The included Sony hood that comes with the RX10 Mark 4 will never vignette the lens and it would be the best at blocking flares.

Q: 7. Will this cause vignetting on a full-frame 35mm lens? (Specifically, the Sony-Zeiss 35mm f1.4 ZA)

A: It is possible that you will experience vignetting even with a short hood although not probably with the 35mm. This usually occurs with wider lenses in general.

Q: 8. How many stops is the VND filter rated for?

A: It is 1.5 to 9 stops.

Q: 9. Does it fits on a Tamron 18-400?

A: Just keep the package! It should fit, but sometimes it just doesn't. Good luck. Odds are it will fit on the tamron 18-400 just fine

Q: 10. Is their a clear insert fir when an ND is bit needed ?

A: The Commlite EF/EF-S to RF mount adapter does not come with a clear-insert filter, and unfortunately it seems we do not carry one that might be purchased separately. We also attempted to slot the Canon OEM clear filter (as well as their CPL and ND filter holders) and they did not fit.