Polymaker 2.85mm PolyMide PA6-CF Filament 2kg Blackfrom Polymaker 2.85mm PolyMide PA6-CF Filament 2kg Blackis a carbon fiber reinforced PA6 (Nylon 6) filament. The carbon fiber reinforcement provides significantly enhanced stiffness, strength, and heat resistance with outstanding layer adhesion. PolyMide PA6-CF is from the PolyMide family of Nylon/polyamide based filaments and features Polymaker's Warp-Free technology, which allows the production of Nylon-based filaments that can be 3D printed with excellent dimensional stability and near-zero warpage. This is achieved by the fine control of microstructure and crystallization behavior of Nylon, which enables the material to fully release the internal stress before solidification.

PolyMide PA6-CF is compatible with most of the 3D printers available on the market. Examples include the Ultimaker, Flashforge, Snapmaker, LulzBot, Raise3D, Flsun, Artillery, Anycubic, Creality, and more.

Please check out the below print settings and other properties, which are based on the use of a 0.4mm nozzle and the Simplify 3D v.4.0 printer.

Carbon Fiber Reinforced PA6 (Nylon 6)    Enhanced Strength and Heat Resistance    Polymaker Warp-Free Technology    536 to 572°F Print Temperatures    30 to 60mm/s Print Speeds

536 to 572°F

30 to 60mm/s

77 to 122°F

Almost any surface with a thin coat of PVA glue or Magigoo PA

Off

Related Questions and Answers

Q: 1. What is the diameter of the base plate (where the tripod head attaches)? Will this fit nicely with the Manfrotto BeFree video head (it's base is 40mm)?

A: The base plate is about 2" wide, and would fit the Manfrotto BeFree video head quite nicely on it.

Q: 2. Is the center column removable and if so then how low it can go to the ground?

A: With the Slik Pro CF-733 Tripod (Black) one can remove the lower part of the center column to get lower to the ground. One can then get down to 8.3" (This does not include the height of any head one may use). Alternatively one can invert the center column to get even lower to the ground.

Q: 3. What is the outside diameter of the top of the center column (where a head would be mounted)?

A: According to Slik USA, the platform plate on the top of the center column on the Slick CF-633 tripod is 1-5/8" in diameter.

Q: 4. Does the center column remove in order to have minimum height of 4"?

A: The bottom main section unscrews leaving just the top portion.

Q: 5. Is the centerpost made of CF or Aluminum?

A: The center column is aluminum.

Q: 6. Will this case fit AF-S NIKKOR 58mm f/1.4G Lens on a D810 ?

A: It should fit fine. The case is meant to fit most small prime lenses. Once you get into longer focal lengths or zooms it won't fit.

Q: 7. Hi, What is the leg tube diameter of the CF-834?

A: Slik Pro CF-834 Tripod is a 4 section leg tripod. Stating from the thinnest to the thickest section they increment as fallow: (19 ,22 , 25, 27mm)

Q: 8. Is this made in Thailand or China?

A: This tripod is manufactured in Thailand.

Q: 9. What is the diameter of the base plate (where the head attaches)? Would the manfrotto befree video head fit on this neatly, says it is best that it be a 40mm base plate?

A: The base plate is about 2" wide, and would fit the Manfrotto BeFree video head quite nicely on it.

Q: 10. Is center column removable?

A: Yes it is!