Polymaker 1.75Mm Polymide Pa612-Cf Filament 500G Black

Polymaker 1.75mm Polymide Pa612-cf Filament 500g Black

Product Code: eq155060
Availability: In Stock

$119.97 $161.96

Qty

10 reviews Write a review

Description
Reviews (10)

The Polymaker 1.75mm PolyMide PA612-CF Filament 500g Blackis made of carbon fiber reinforced polyamide, which is based on a copolymer of PA6 and PA12. Thanks to its chemical structure, this filament has a lower moisture sensitivity compared to PA6-based materials, and improved mechanical properties compared to PA12-based materials. This filament enhances dimensional stability, thanks to carbon fiber reinforcement and warp-free technology.

1.75mm Filament Diameter 500g Weight Nylon Material

Parameters
Filament Diameter	1.75 mm
Filament Material	Nylon
Color	Black
Weight	1.1 lb / 500 g
Packaging Info
Package Weight	1.87 lb
Box Dimensions (LxWxH)	9 x 8.4 x 2.8"

Printing Temperature: 482 - 572°F / 250 - 300°C
Bed Temperature: 77 - 122°F / 25 - 50°C
Printing Speed: 30 - 60 mm/s
Fan: OFF

Direct Drive

Retraction Distance: 3 mm
Retraction Speed: 40 mm/s

Indirect Drive

Retraction Distance: 6 mm
Retraction Speed: 60 mm/s

212°F / 100°C for 8 hours (Only if the material has absorbed moisture)

Related Questions and Answers

Q: 1. Will this case fit AF-S NIKKOR 58mm f/1.4G Lens on a D810 ?

A: It should fit fine. The case is meant to fit most small prime lenses. Once you get into longer focal lengths or zooms it won't fit.

Q: 2. What is the diameter of the base plate (where the tripod head attaches)? Will this fit nicely with the Manfrotto BeFree video head (it's base is 40mm)?

A: The base plate is about 2" wide, and would fit the Manfrotto BeFree video head quite nicely on it.

Q: 3. Is this made in Thailand or China?

A: This tripod is manufactured in Thailand.

Q: 4. Does the center column remove in order to have minimum height of 4"?

A: The bottom main section unscrews leaving just the top portion.

Q: 5. What is the diameter of the upper CF legs?

A: Diameter of the first upper leg is; 25mm.

Q: 6. What is the length of the center column?

A: While the manufacturer does not list the total length of the center column, Slik USA does indicate that the maximum height when the center column is down is 48.8 inches, and the maximum height when the center column is fully extended is 64.2 inches. As such, the center column would have 15.4 inches (39.11 cm) of travel from the lowest to highest setting.

Q: 7. Is the case meant to stay on the strap while shooting?

A: Yes, the case stays on the strap when you are shooting.

Q: 8. What is the outside diameter of the top of the center column (where a head would be mounted)?

A: According to Slik USA, the platform plate on the top of the center column on the Slick CF-633 tripod is 1-5/8" in diameter.

Q: 9. What is the thread size?

A: This tripod has a reversible screw. One side is 1/4" the other side is 3/8".

Q: 10. Hi, What is the leg tube diameter of the CF-834?

A: Slik Pro CF-834 Tripod is a 4 section leg tripod. Stating from the thinnest to the thickest section they increment as fallow: (19 ,22 , 25, 27mm)

David	26/09/2024
[1.87 lb] Polymaker is one of the best filaments out there and for sure the best company out there I can think of. They do so much good for the community so I'm always more than happy to support them any way I can. This stuff prints like a dream. 5

Mikel	25/09/2024
[1.87 lb] This Teal PLA turned out great. Inky has been out front for about 6 months under various weather condition and no issues. This turned out to be the best looking Teal for Inky. 5

Daniel	17/09/2024
[Nylon] This stuff is impressive. It has a much higher tolerance for printing fine pieces. Its sand-able and workable and much more rigid than PLA. It does have some issues I'm finding joints aren't as well supported because of the fiber content versus plastic but once I engineer the model to accommodate, it works amazingly well. 5

Mikel	26/08/2024
[Black] Clyde has been out for 6 months under various weather conditions. This Orange PLA turned out great for Clyde. 5

Mikel	06/08/2024
[1.87 lb] Pinky has been in my front lawn for about 6 months. This Pink is the best Pink PLA for Pinky. 5

Daniel	05/08/2024
[Black] This gold is the same as any other, the color is vibrant and the silk effect works well. Polymaker tends to be my go-to for these types of base material colors because the material works well, and I have the least number of issues for the price point. 5

Daniel	15/07/2024
[9 x 8.4 x 2.8"] This material is one of my hands down favorites. The color intensity is truly a charcoal black. To me, it beats all other silk materials because of its light diffusing properties. Its rough to the touch and doesn't have the dry time CF does. Fantastic material and I will keep buying it again and again 5

Thomas	16/05/2024
[1.75 mm] This item arrived quickly from BH Photo. It was packed well with no damage. The storage box is large and can allow 2 1kg rolls or one larger roll to be stored. It has a nice dessicant storage space and humidity guage. It is a bit pricey since you can also get a heated drier/storage box that is less money now days. I just wanted a box without the cord attached. 5

Daniel	15/04/2024
[1.87 lb] This stuff is fantastic. I don't see much of a difference in color, versus other materials of the same color but this material has had the least number of issues along with the bulk of the prints I have made with it. I tend to like polymaker in general for standard colors and base materials so, I will purchase this again when needed. 5

Mikel	14/04/2024
[1.75 mm] This took two spools of yellow to create this basketball size Pac Man for my front yard garden. This yellow PLA turned out great and has weathered for about 6 months with no discoloration. 5