The Whirlwind NAC3X-001.5 powerCON TRUE1 is a 1.5' power cable for linking Whirlwind PL1T-420 boxes together. This is Neutrik’s first true mains connector with breaking capacity according to IEC 60320 and UL 498 standard and thus allows disconnecting under load. The UL and VDE certified, single-phase system is designed for 16A, 250V. The cable connector comes with an integrated twist-lock and can only be opened with a tool. All Powerlink products are hand-wired in Rochester, NY, USA.

Powercon True1 Inlet to Powercon True1 Outlet for Linking Whirlwind PL1T-420 Boxes Together

Related Questions and Answers

Q: 1. Does this unit require external power? if so, how much and on what kind of connector?

A: The Whirlwind Line Balancer/Splitter requires no external power and is designed to split a single line level input signal into two balanced line level outputs. A choice of two output configurations is provided: one direct output and one isolated output, or two isolated outputs. The Line Balancer/ Splitter uses Whirlwinds TRSP-600L transformer and has a frequency response of 20 to 20kHz, 1dB @ +2OdBm.On the Line Balancer/Splitter are two male XLR jacks, one female XLR jack, a 14 jack and three switches as outlined below:INPUTEither of the two input connectors, a female XLR jack or a 14 TRS jack (Tip = Pin 2 and Ring = Pin 3) can be used for connection from a line level source, balanced or unbalanced. Use only one input at a time.OUTPUTSThe male XLR output connectors can be configured in one of two ways. The ISOLATED OUT/SPLIT 1 is always transformer isolated and the DIRECT OUT/SPLIT 2 is either directly connected to the input or transformer isolated, depending on the position of the OUTPUT SELECT switch.OUTPUT SELECTThis push-button switch selects the output mode of the unit. In the out position, the DIRECT OUT/SPLIT 2 provides a direct output signal and the ISOLATED OUT/SPLIT 1 provides a balanced 600 isolated signal. In the in position (the center of the switch changes to orange) both output connectors provide a balanced 150 ?isolated signal that is attenuated by 6dB from the input.GND/LIFTSEach of these switches disconnects the ground between the inputs and the XLR outputs when set to the LIFT position. Grounds remain connected when set to the GND position.This product is warranted to be free of defects in materials or workmanship to the original purchaser for a period of 3 years from the date of purchase.

Q: 2. Can you use an additional inline barrel pad on top of this in case you need to knock a signal down to mic level?

A: The output is already at mic level. The transformer gives you a 20 dB loss from -10 consumer line input to -30dB. If you need more, there is a built in 20 dB pad switch which takes your signal down to -50dB total. There is no reason or need to use an additional pad.

Q: 3. SmallRig battery

A: The Lentequip SafeTap Connector will work with any Battery brand that has a D-TAP/P-TAP connector on the battery. Assembly info: https://bit.ly/47J2JDP

Q: 4. Is this the latest version with ground protection?

A: Yes it is. This is the latest version of the Lentequip SafeTap Connector and it features Ground Protection.

Q: 5. Do you need two boxes for the producer to talk to the talent or can you simply plug a microphone into one of the XLR inputs to talk to talent?

A: No you can plug the mic out from the box into one of the mic input channels of the mixer. Then the talent will hear you through the cue mix from the Aux sends.

Q: 6. Can I buy the power supply separate?

A: The power supply can be ordered from your dealer. it is model # PS12AC1A.

Q: 7. So with this one box i can have two announcers or is it one announcer per box?

A: The THS boxes are designed for use by one announcer.

Q: 8. do you have to have a mixer to use this?

A: No. I use it to go from stereo 1/8 sources (like laptops and cell phones) to one or two XLR's that I then put into a mixer, personally. But you could plug your XLR's into a combo amp or whatever else you want.

Q: 9. What's the barrel plug size?

A: That information is not listed as this is designed specifically to work with the Sigma SAC-7P AC Adapter, BH #SISAC7P. If you have that adapter, this will work with it.

Q: 10. Can you reverse this device, similar to how the PC/DI can be used both directions?

A: The PCUSB cannot be used backwards as it has active circuitry.