Take control of your modular signals with the 4ms Catalyst Controller, a macro controller with eight precision CV outputs and a responsive crossfader to morph between scenes. Each scene is a snapshot of up to eight CV outputs, which can work like a modular preset. Jump to different scenes with the dedicated scene buttons or traverse a pathway composed of multiple scenes using the crossfader or an external CV signal. Record CV and slider movements, and play recordings back via a button or external trigger.

Each precision output has a maximum range of -5V to +10V. Channels have an adjustable morphing curve that can be quantized to common scales, restricted to a particular voltage range or set to output gates. Whether used as a CV preset manager, seamless transition generator, chord sequencer, CV recorder, or experimental CV playground, the Catalyst Controller puts control of your modular at your fingertips.

Eight-Channel Macro Controller    Crossfader Morphs Between Scenes    CV Preset Manager, Transition Generator    Chord Sequencer, CV Recorder    Experimental CV Playground    Each Channel Can be CV or Gate    Arrange Up to 64 Scenes into Pathways    Adjustable Slew/Lag Time    Includes Power Cable + Mounting Screws

• Smooth, responsive crossfade morphs between scenes
• Eight output channels, each can be CV or Gate
• Arrange scenes into pathways of up to 64 scenes
• Smooth, responsive crossfader morphs from scene to scene along the pathway
• Set slew/lag to limit how fast scenes can change
• Adjustable Morph time per output
• Control crossfading with an external CV
• Record and playback up to 20 seconds of CV and crossfader motion
• CV outputs can be set to -5V to +10V maximum, or limited to +/-5V, +5V, +3V, or +1V
• CV outputs can be unquantized (sub-1mV resolution), or Quantized to common scales
• Randomization of channel values/gates
• Copy/paste
• Based on the original Catalyst from Emblematic Systems

The Catalyst Controller can also turn into a Catalyst Sequencer. Hold down a special button combination to change between controller and sequencer modes. If you end up liking the Sequencer more, you can even remove the double-sided faceplate, flip it over, and reinstall with the Sequencer artwork visible.

• 20 HP Eurorack format module
• Includes power ribbon cable with 10-pin Eurorack power header
• Power consumption: +12V: 60mA, -12V: 25mA

Related Questions and Answers

Q: 1. Will this work with SONY HDR-CX230 ?

A: It will not. This controller is not compatible with the CX230.

Q: 2. Does this work with the FX9 and Sony 28-135 lens combo?

A: Yes, the MagnusVC-20-SCP LANC Zoom Controller will connect to the SONY FX9's LANC input, and control a SONY PZ lens like the Sony FE PZ 28-135mm f/4 G OSS Full-Frame Power Zoom Lens. Please note you will not need to use the AVR cable with the kit.

Q: 3. Is there a replacement cable for this device? The 2.5mm cable.

A: The unit I bought uses a male to male 3.5 tsr cable between the zoom control and the camera.

Q: 4. Will this work with the Sony HXR-NX100 Full HD NXCAM Camcorder?

A: Yes.

Q: 5. Is this compatible with Canon C100/200/300 cinema line cameras?

A: It is not.

Q: 6. Will this work with a Sony HXR-NX30U? What is the length of the cable?

A: I could not tell you, I could not make it work with the Sony hxr-nx100

Q: 7. Would this work with a Sony FS100 and one of Sony’s power zoom lenses?

A: Yes, this device will work.

Q: 8. Does this controller also work with the older Panasonic models DVX100B AND HPX170?

A: Most likely it will.

Q: 9. Is this compatible to my Canon XA40 Camcorder???

A: Yes it is. This is a LANC controller and the XA40 is a LANC compatible camcorder.

Q: 10. is this compatible with canon DSLRs and lenses?

A: This is designed to run with the servo mechanisms attached to zoom lenses on professional cameras. It uses a common ENG connector, which is a circular connector, has 8 pins, and is about 1/2 in diameter. I can't imagine that any DLSR would be compatible.