The Burris FastFire III Red-Dot Reflex Sightfrom Burris FastFire III Red-Dot Reflex Sightfeatures a 3-MOA red aiming dot, which is big enough to see in the daylight but won't obstruct small varmints. Three brightness levels lets you set it to your preference, or switch it to auto and the light sensor will detect the amount of available light and adjust the brightness itself. The FastFire III is made of aluminum with a matte-black anodized finish, and is waterproof and submersible. This sight comes with a Picatinny/Weaver rail mount, and mounts for a variety of rifles and pistols are also available that allow you to move the FastFire to other firearms.

3-MOA Red Aiming Dot    Three Brightness Levels with Auto Mode    1 MOA Impact Point Correction    30 MOA Per Rotation Travel    ±90 MOA Windage/Elevation Adjust    Anodized Aluminum Housing    Waterproof and Submersible    Picatinny/Weaver Rail Mount

• 1x magnification
• 0.8 x 0.6" objective lens window
• Fully coated optics for increased light transmission

• 3-MOA red dot with three intensity levels and an automatic brightness mode
• 1 MOA impact point correction, 30 MOA per rotation travel
• ±90 MOA windage and elevation adjustment range
• Parallax-free from 10 to 150 yd

• Aluminum housing
• Matte-black corrosion and scratch-resistant anodized finish
• Top-loading battery compartment enables battery changes without removing the sight
• Included Picatinny/Weaver rail mount
• Waterproof and submersible

Related Questions and Answers

Q: 1. Will this mount to a beretta 1301 ?

A: According to Trijicion the RM06 RMR Type 2 Adjustable LED Reflex Sight (3.25 MOA Red Dot, Cerakote Flat Dark Earth) BH #TRRM06CKFDE • MFR #RM06-C-700696 is Engineered for use with pistols, rifles, or shotguns

Q: 2. Is this scope magnified ? If so to what power?

A: The Burris Optics FastFire III 8-MOA Red-Dot is 1x magnification.

Q: 3. Will it fit on a S&W M&P pistol?

A: I purchased the FastFire III w/picatinny mount, but ended up removing the Picatinny and purchasing the mount specific to my Ruger Mark III. Much cleaner lower profile installation. I believe there is a S&W mount. Threaded portion slides into dovetail then mount attaches with 2 or 3 screws. Easy..no gunsmith required.

Q: 4. Does this come with mounting hardware?

A: Yes it would come with a Mounting Set. Included In the Box would be the following. Trijicon RM06 RMR Type 2 Adjustable LED Reflex Sight (3.25 MOA Red Dot, Matte Black) Trijicon Sticker CR2032 Lithium Battery Mounting Set Limited Lifetime Warranty Limited 5-Year Warranty

Q: 5. I want to fit this to my tripod foot on my Canon EF 300 f/2.8 and my EF 400 f/5.6 lenses , can I bolt weaver rails to the tripod feet ?

A: The tripod foot has a 1/4-20" thread, if you can use bolts for the rail that are that size, yes.

Q: 6. what battery goes in the scope?

A: The Barska 30mm Red Dot Sight comes with a CR2032 Lithium Battery.

Q: 7. Does the integrated mount fit a weaver rail?

A: Yes the Barska 30mm Red Dot Sight will fit a Weaver rail.

Q: 8. Does it come with mounting screws?

A: Yes it does. The site itself fits snug, however the supplied torx screws draw it right where it seats properly.

Q: 9. will this sight fit on my rock island 22tcm pistol?

A: Unfortunately there is no mount for the Trijicon RM02 RMR Type 2 LED Reflex Sight to be mounted on a Rock Island TCM. About your only choice would be to take it to a qualified gunsmith. Have him install a picatinny rail or mill the slide for a dove tail mount.

Q: 10. Which mounting plate would I need for a Glock 19X ?

A: If the Glock 19 x is the mos version all you would need is the #2 from glock. If it is the non MOS you would would need replace RM44, or send out the gun to have it fitted for this.