Streamline your installation process while also giving your system ample power with the Corsair RM1000x SHIFT 80 PLUS Gold Modular Power Supply. Not only does the SHIFT allow you to pick and choose the cables you need for your equipment, but it also places Corsair's Type 5 Gen 1 micro-fit PSU connectors on the side, working alongside your dedicated cable management spaces for a more organized experience.

Offering up to 1000W and built off the ATX 12V Version 3.0 standard, you are able to deliver ample power to your gaming-focused components with ease while balancing electrical loads. Modular cable design allows you to pick and choose which cables you need or want to use depending on your system's configuration, giving you more breathing room inside the case while reducing cable clutter. Aside from the standard motherboard and CPU cables, you also get an array of PCIe cables giving you a total of seven connectors between three 6+2 connectors on one cable and two 6+2 connectors on two split cables. For NVIDIA 40 series graphics cards, a single dedicated 12VHPWR cable is included that further reduces cable clutter. You also get 16 SATA connections and eight PATA connectors for storage drives and peripherals, respectively.

1000W Total Wattage    ATX 12V Version 3.0    12VHPWR Cable    7 x PCIe Connectors    16 x SATA Connectors    8 x PATA Connectors    Modular Cable Design    Side-Panel Connectors    140mm FDB Cooling Fan    80 PLUS Gold Efficiency

The SHIFT incorporates a unique design that places the traditional PSU-based connectors on the side as opposed to the rear of the unit, giving you a clear view of your connectors and streamlining your installation process when working in cases with side-accessible cable management areas.

The ATX 3.0 standard demands a high level of reliability and power efficiency, meeting the 80 PLUS Gold certification, giving you up to 87% and 90% efficiency at full- and half-loads, respectively.

A low-friction, fluid dynamic bearing 140mm fan with Zero RPM mode support ensures your PSU runs cool while staying virtually silent when not under high load.

Built with 100% Industrial-grade, 105°C-rated Japanese electrolytic capacitors for unwavering power and reliability.

The PSU and cables will fit in any PC case that supports ATX PSU format and is at least 8.3" (210mm) wide. The PSU must also be accessible from the side when mounted in the case.

Related Questions and Answers

Q: 1. Compatible with the older Impact 16 POWER SYNC ?

A: Yes this unit is compatible with the original Impact PowerSync 16 Transmitter and Receivers.

Q: 2. Is this unit compatible with the Powersync16 transmitter & reciever?

A: Yes, the PowerSync 16-80 is backward compatible with PowerSync 16 but limited to 16 channels.

Q: 3. Good day, will it be synchronized if I put it on Nikon D850 with Godox Professional Studio Flash?

A: It would be synchronized if you buy 2 transceivers - with the included PC cable

Q: 4. Is the Impact PowerSync 16-80 Transceiver compatible with the pocket-wizard Plus III ? I have several Pocket wizards and would like to expand with the impact poer synk 16-80

A: No. The different manufacturers use different frequency ranges. Sometimes these frequency ranges are different even among models of the same manufacturer. You must always check if different models are compatible.

Q: 5. I have a HVL-F60M flash that I use with the Sony A7r. Will this trigger be compatible to use with both the flash I have and the A7r? I am assuming I will need to purchase 2 units - one for the camera and the other for the flash, right? Thank you,Nicholas Lutfi

A: Unfortunately, Impact does not list the devices that use the Sony Multi-Interface Shoe like the A7R and the HVL-F60M flash as compatible with the Powersync 16-80 Transceiver. As an alternative, you can use the PocketWizard PlusX 2 Pack along with an adapter for the flash to connect one Plus X unit. Please see the images below for reference.

Q: 6. can this be used on a canon 70d?

A: It should work on any camera with a hotshoe, so yes. Remember that you will need two of them (two transceivers, or one transmitter for the camera, and one receiver for the flash.

Q: 7. Does this plate work with the Dracast LED 500?

A: This plate is for LED500 Pro and Plus LED Panels.

Q: 8. It is Yongnuo flashes compatible?

A: No idea bro. I have nikon sb 700 and it works ONLY in manual mode. For me it's perfect...

Q: 9. Is the Zoom feature Windows controlled or is it separate download?

A: You have to download the PTZOptics Webcam OSD from the PTZoptics website.

Q: 10. Good day, may I know if this transceiver support HSS and TTL? I also want to believe it should be able to work with old Minolta/Sony flash like the 5600 HS Shoe Mount Xenon Flash (For Minolta) and Sony ILCA-A77M2 while also using the necessary adapters like the TF-323 SONY & Minolta TTL Hot Shoe to PC Sync Adapter.

A: The Impact PowerSync16-80 Transceiver is a fully manual transceiver. It does not have TTL or high Speed Sync capabilities. As the Minolta 5600HS Flash does not have a PC sync terminal, you would need to purchase a hot shoe adapter such as the Vello HSA-CSMSA Multi-Interface to Sony/Minolta Shoe Adapter, B&H # VEHSACSMSA, to connect the Impact PowerSync 16-80 Transceiver to the Minolta 5600HS Flash.